Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

The knock control sensor is fitted onto the engine block to detect engine knocking.

The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the knock control sensor is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor circuit

·

Knock control sensor

·

ECM


Comes on DTC stored
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) The output voltage of the knock control sensor is higher than 4.5 V for 1 second or more (1 trip detection logic).
·

Open in knock control sensor circuit

·

Knock control sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the power switch is turned off.


Reference: Inspection using an oscilloscope

A306156E01
2.396,0.167 3.302,0.49 0.906,0.323 10 false 1 V/DIV. 2.625,0.969 3.292,1.292 0.667,0.323 10 false GND 1.094,1.885 2.229,2.177 1.135,0.292 10 false 1 ms./DIV.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock control sensor remains low or high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

The monitor for DTCs P0327 and P0328 begins to run when 5 seconds have elapsed since the engine was started.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and wait 5 minutes.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0327 or P0328.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A255200E03
1.23,1.778 2.616,1.951 1.386,0.174 10 Knock Control Sensor 3.558,2.475 4.221,2.659 0.663,0.184 10 Shielded 5.966,3.326 6.313,3.49 0.347,0.163 10 ECM 5.527,1.116 5.919,1.279 0.392,0.163 10 KNK1 5.527,1.942 5.947,2.106 0.42,0.163 10 EKNK 5.162,1.116 5.423,1.269 0.26,0.153 10 123 5.162,1.944 5.419,2.097 0.257,0.153 10 124 1.216,1.62 1.407,1.783 0.191,0.163 10 Y1 1.007,1.116 1.114,1.279 0.108,0.163 10 1 2.7,1.116 2.808,1.279 0.108,0.163 10 2 5.648,3.326 5.922,3.49 0.274,0.163 10 E28

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Start the engine.


f.

Warm up the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Knock Feedback Value.

Powertrain > Engine and ECT > Data List
Tester Display
Knock Feedback Value
50003 234 192

h.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock Feedback Value changes
Malfunctions occur Knock Feedback Value does not change

The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by racing the engine.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
a.
A194105C53
0.573,2.104 0.969,2.344 0.396,0.24 0.26,0.198 0.469,0.365 0.208,0.167 10 false *a 0.698,2.156 0.896,2.344 0.198,0.188 10 false Y1
*a Front view of wire harness connector
(to Knock Control Sensor)


Disconnect the knock control sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y1-2 - Y1-1 Power switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT KNOCK CONTROL SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
3.INSPECT KNOCK CONTROL SENSOR
a.

Inspect the knock control sensor.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>KNOCK SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock control sensor.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
a.

Disconnect the knock control sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-2 - E28-123 (KNK1) Always Below 1 Ω
Y1-1 - E28-124 (EKNK) Always Below 1 Ω
Y1-2 or E28-123 (KNK1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR