Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E19
4.773,0.815 6.439,1.027 1.666,0.212 10 Camshaft Position Sensor 4.744,1.325 6.468,1.486 1.724,0.161 10 Crankshaft Position Sensor 0.072,0.015 0.944,0.215 0.873,0.2 10 VVT System: 2.337,1.96 3.614,2.135 1.277,0.175 10 Target Valve Timing 2.337,1.288 3.614,1.463 1.277,0.175 10 Actual Valve Timing 2.687,2.696 3.401,2.871 0.714,0.175 10 Correction 2.826,3.204 3.228,3.379 0.402,0.175 10 ECM 1.602,3.75 4.49,3.934 2.887,0.185 10 Camshaft Timing Oil Control Valve Assembly 0.17,2.69 0.865,2.865 0.695,0.175 10 Duty-cycle 4.531,1.835 6.76,2.058 2.229,0.222 10 Mass Air Flow Meter Sub-assembly 4.454,2.856 6.752,3.055 2.298,0.199 10 Engine Coolant Temperature Sensor 4.84,2.344 6.374,2.512 1.534,0.168 10 Throttle Position Sensor 4.889,3.361 6.325,3.541 1.437,0.18 10 Vehicle Speed Sensor 0.317,4.27 1.686,4.475 1.369,0.205 10 Engine Oil Pressure 3.663,4.217 7.056,4.401 3.392,0.184 10 VVT Controller (Camshaft Timing Gear Assembly) 3.887,4.918 4.988,5.102 1.101,0.184 10 Intake Camshaft 2.566,4.571 2.846,4.275 2.846,4.275 3.611,4.275 false 3.181,4.782 3.323,5.009 3.323,5.009 3.856,5.009 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255118E43
0.604,1.865 2.385,2.24 1.781,0.375 10 false Camshaft Timing Oil Control Valve Assembly 0.24,1.865 1.052,2.219 0.813,0.354 10 false E63 1.594,0.802 2.156,1.281 0.563,0.479 10 false 1 1.594,1.438 2.01,1.708 0.417,0.271 10 false 2 4.865,0.802 5.385,1.24 0.521,0.438 10 false 74 4.865,1.438 5.448,1.771 0.583,0.333 10 false 75 5.125,1.448 5.698,1.74 0.573,0.292 10 false OC1- 5.135,0.813 5.76,1.188 0.625,0.375 10 false OC1+ 5.656,2.24 6.188,2.49 0.531,0.25 10 false ECM 5.323,2.229 5.833,2.531 0.51,0.302 10 false E28

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (DTC P0010)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

i.

Start the engine and allow the engine to idle.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0010 is output A
DTC is not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E63-1 - E28-74 (OC1+) Always Below 1 Ω
E63-2 - E28-75 (OC1-) Always Below 1 Ω
E63-1 or E28-74 (OC1+) - Body ground Always 10 kΩ or higher
E63-2 or E28-75 (OC1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR