Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0403  Exhaust Gas Recirculation Control Circuit  


DESCRIPTION

Refer to DTC P0401 (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>P0401).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0403 Exhaust Gas Recirculation Control Circuit Open or short in EGR valve circuit (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored

HINT:

DTC P0403 is stored when the power switch is on (IG).


MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.

Example:

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit, and stores the DTC.

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, and stores the DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A215251E08
2.329,2.896 2.916,3.225 0.587,0.33 10 Warming Up 3.406,2.896 4.119,3.086 0.714,0.19 10 10 minutes 2.025,2.046 2.223,2.234 0.198,0.188 10 [A] 2.532,1.777 2.757,1.967 0.225,0.19 10 [B] 3.781,0.69 3.993,0.877 0.212,0.188 10 [C] 4.44,3.293 4.679,3.464 0.239,0.171 10 [D] 0.737,0.817 1.79,0.991 1.053,0.174 10 20 km/h or more 1.435,1.902 1.808,2.074 0.373,0.172 10 Idling 0.886,2.204 1.799,2.576 0.913,0.372 10 Power Switch on (IG)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up [B].

8.

Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0403.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system has a normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A269014E01
1.777,5.235 3.133,5.406 1.355,0.171 10 EGR Valve Assembly 0.702,4.761 1.337,5.105 0.635,0.344 10 Auxiliary Battery 0.612,3.84 1.282,3.994 0.67,0.154 10 MAIN 2.759,0.859 3.475,1.043 0.716,0.184 10 EFI NO. 3 2.103,1.366 2.829,1.52 0.726,0.154 10 EFI MAIN 5.835,1.114 6.272,1.267 0.436,0.154 10 MREL 5.481,1.114 5.779,1.267 0.297,0.154 10 A25 5.555,0.933 5.742,1.087 0.187,0.154 10 46 1.424,5.235 1.721,5.389 0.297,0.154 10 E24 5.527,2.744 5.748,2.898 0.221,0.154 10 28 5.527,3.136 5.748,3.29 0.221,0.154 10 27 5.527,3.529 5.748,3.683 0.221,0.154 10 26 5.527,3.921 5.748,4.075 0.221,0.154 10 25 3.061,2.826 3.205,2.98 0.144,0.154 10 4 3.061,3.218 3.205,3.372 0.144,0.154 10 3 3.061,3.611 3.205,3.765 0.144,0.154 10 6 3.061,4.76 3.205,4.914 0.144,0.154 10 5 3.061,4.395 3.205,4.549 0.144,0.154 10 2 3.061,4.003 3.205,4.157 0.144,0.154 10 1 5.835,2.919 6.241,3.073 0.406,0.154 10 EGR1 5.835,3.314 6.241,3.468 0.406,0.154 10 EGR2 5.835,3.699 6.241,3.853 0.406,0.154 10 EGR3 5.835,4.091 6.241,4.245 0.406,0.154 10 EGR4 2.585,2.826 3.0,2.98 0.415,0.154 10 EGR1 2.585,3.218 3.0,3.372 0.415,0.154 10 EGR2 2.585,3.611 3.0,3.765 0.415,0.154 10 EGR3 2.712,4.774 3.002,4.928 0.289,0.154 10 +B2 2.717,4.395 3.002,4.549 0.285,0.154 10 +B1 2.585,4.003 3.0,4.157 0.415,0.154 10 EGR4 5.479,4.091 5.752,4.245 0.273,0.154 10 E28 5.479,3.699 5.752,3.853 0.273,0.154 10 E28 5.479,3.314 5.752,3.468 0.273,0.154 10 E28 5.479,2.919 5.752,3.073 0.273,0.154 10 E28 0.618,2.289 1.801,2.443 1.183,0.154 10 EFI-MAIN NO. 1 6.089,4.791 6.426,4.945 0.337,0.154 10 ECM 1.69,0.703 1.926,0.884 0.236,0.181 10 1B 1.69,1.113 1.926,1.294 0.236,0.181 10 1E 3.504,1.113 3.741,1.294 0.236,0.181 10 1C 3.504,0.698 3.741,0.878 0.236,0.181 10 1A 1.74,0.508 1.897,0.65 0.157,0.142 10 1 1.74,0.925 1.86,1.126 0.12,0.201 10 2 3.565,0.925 3.685,1.126 0.12,0.201 10 7 3.552,0.504 3.657,0.665 0.105,0.161 10 8 1.996,1.739 3.55,1.893 1.554,0.154 10 No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP and Throttle Idle Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
MAP
Throttle Idle Position
50004 234 42 4,296

g.

Confirm that the Throttle Idle Position is ON and check the MAP values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly maybe a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result:
Proceed to
OK
NG




OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.

Inspect the EGR valve assembly.

Click hereEngine / Hybrid System>2AR-FXE EMISSION CONTROL>EGR VALVE>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)
A209148C16
0.25,1.792 0.625,2.073 0.375,0.281 1.813,2 2.667,1.083 2.667,1.083 2.833,1.083 false 2.583,2.948 1.823,2.385 false 0.313,1.854 0.646,2.031 0.333,0.177 10 false E24 0.229,0.188 0.448,0.365 0.219,0.177 10 false *a 2.667,2.938 2.99,3.115 0.323,0.177 10 false +B2 2.906,1.01 3.229,1.188 0.323,0.177 10 false +B1
*a Front view of wire harness connector
(to EGR Valve Assembly)


a.

Disconnect the EGR valve assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E24-2 (+B1) - Body ground Power switch on (IG) 11 to 14 V
E24-5 (+B2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
E24-4 (EGR1) - E28-28 (EGR1) Always Below 1 Ω
E24-3 (EGR2) - E28-27 (EGR2) Always Below 1 Ω
E24-6 (EGR3) - E28-26 (EGR3) Always Below 1 Ω
E24-1 (EGR4) - E28-25 (EGR4) Always Below 1 Ω
E24-4 (EGR1) or E28-28 (EGR1) - Body ground Always 10 kΩ or higher
E24-3 (EGR2) or E28-27 (EGR2) - Body ground Always 10 kΩ or higher
E24-6 (EGR3) or E28-26 (EGR3) - Body ground Always 10 kΩ or higher
E24-1 (EGR4) or E28-25 (EGR4) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the EGR valve assembly connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
E24-2 (+B1) - 1A-8 Always Below 1 Ω
E24-5 (+B2) - 1A-8 Always Below 1 Ω
E24-2 (+B1) or 1A-8 - Body ground Always 10 kΩ or higher
E24-5 (+B2) or 1A-8 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR