Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0ADC-226 | Hybrid Battery Positive Contactor Control Circuit High | Open or short to +B in the SMRB circuit | ·
Wire harness or connector ·
Hybrid battery junction block assembly ·
Power management control ECU |
Does not come on | Master Warning Light:
Comes on |
Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
If P0ADC-226 is stored, the vehicle cannot be started.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / SMRB Status.
| Tester Display |
|---|
| SMRB Status |
Read the Data List.
| Tester Display | Switch Condition | Specified Condition |
|---|---|---|
| SMRB Status | Power switch on (IG) | OFF |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).
Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
The connector is connected securely and there are no contact pressure problems.
Install the No. 4 hybrid battery shield panel.
| Proceed to |
|---|
| OK |
| NG |
OK
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Power Management Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-4 (SMRB) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector I3 from the power management control ECU.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-4 (SMRB) - Body ground | Power switch off | 25.0 to 59.0 Ω |
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 Fuse |
Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.
Remove the No. 4 hybrid battery shield panel.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL
Disconnect connector O9 from the hybrid battery junction block assembly.
Disconnect all the connectors from the power management control ECU.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-4 (SMRB) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-4 (SMRB) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connectors.
Connect the hybrid battery junction block assembly connector.
Install the No. 4 hybrid battery shield panel.
Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).
Disconnect connector O9 from the hybrid battery junction block assembly.
Disconnect connector I3 from the power management control ECU.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
| *b | Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-4 (SMRB) - O9-1 (SMRB) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-4 (SMRB) and O9-1 (SMRB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connector.
Connect the hybrid battery junction block assembly connector.
Install the No. 4 hybrid battery shield panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).
Disconnect connector O9 from the hybrid battery junction block assembly.
| *a | Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O9-2 (GND) - Body ground | Power switch off | Below 1 Ω |
Connect the hybrid battery junction block assembly connector.
Install the No. 4 hybrid battery shield panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the hybrid battery junction block assembly (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).
| *a | Component without harness connected
(Hybrid Battery Junction Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O9-1 (SMRB) - O9-2 (GND) | -40 to 80 °C (-40 to 176°F) | 25.0 to 59.0 Ω |
Install the hybrid battery junction block assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
NG