When selecting ECO mode, the ECO mode switch (eco switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.
| Proceed to |
|---|
| A |
| B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| A |
| B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / Combination Meter / Active Test / Indicat. ECO Mode.
Perform the "Indicat. ECO MODE" Active Test.
| Tester Display |
|---|
| Indicat. ECO MODE |
The ECO mode indicator light comes on or blinks.
| Proceed to |
|---|
| A |
| B |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Switch.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ECO Mode | ECO mode transition availability | ON or OFF | In ECO mode: ON | - |
| Tester Display |
|---|
| ECO Mode |
| Result | Proceed to |
|---|---|
| The intelligent tester display changes according to the ECO mode switch (integration control and panel sub-assembly) operation. | A |
| The intelligent tester display does not changes according to the ECO mode switch (integration control and panel sub-assembly) operation. | B |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / Air Conditioning / Data List / ECO Switch.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ECO Switch | ECO mode switch (eco switch assembly) condition | ON or OFF | ECO mode switch (eco switch assembly) being pushed and held: ON
ECO mode switch (eco switch assembly) not pushed: OFF |
- |
| Tester Display |
|---|
| ECO Switch |
| Result | Proceed to |
|---|---|
| The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. | A |
| The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. | B |
A
B
Remove the ECO mode switch (eco switch assembly).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>ECO SWITCH>COMPONENTS
| *a | Component without harness connected
(ECO Mode Switch (Eco Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I49-9 (ECU) - I49-6 (E) | ECO mode switch (eco switch assembly) being pushed and held | Below 1 Ω |
| ECO mode switch (eco switch assembly) not pushed | 10 kΩ or higher |
Install the ECO mode switch (eco switch assembly).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector I49 from the ECO mode switch (eco switch assembly).
| *a | Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I49-6 (E) - Body ground | Always | Below 1 Ω |
Connect the ECO mode switch (eco switch assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector I77 from the air conditioning amplifier assembly.
Disconnect connector I49 from the ECO mode switch (eco switch assembly).
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I49-9 (ECU) - I77-4 (ECOS) | Always | Below 1 Ω |
| I49-9 (ECU) or I77-4 (ECOS) - Body ground | Always | 10 kΩ or higher |
Connect the ECO mode switch (eco switch assembly) connector.
Connect the air conditioning amplifier assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG