Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C73-776  Motor Electronics Coolant Pump "A" Control Performance  


DESCRIPTION

The inverter water pump assembly transmits rotation revolution speed information to the power management control ECU. The power management control ECU monitors the revolution speed and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low or stop) or an intermittent stop malfunction (operation stops intermittently when the speed revolution is abnormal) occurs in the inverter water pump assembly.
·

Inverter cooling system

·

Wire harness or connector

·

Inverter water pump assembly

·

Power management control ECU


Comes on Master Warning Light:
Comes on

HINT:

The inverter water pump assembly operates when the power switch is on (READY).


Related Active Test
DTC No. Active Test
P0C73-776 Activate the Water Pump*1

*1: This is an Active Test of the inverter water pump assembly.

WIRING DIAGRAM

A259912E05
1.604,3.313 2.031,3.5 0.427,0.188 10 false IGCT 0.542,2.74 1.292,2.927 0.75,0.188 10 false IGCT-MAIN 5.479,1.031 5.823,1.198 0.344,0.167 10 false IWP 4.354,0.99 4.698,1.156 0.344,0.167 10 false SWP 4.333,1.417 4.688,1.583 0.354,0.167 10 false NWP 3.625,1.417 3.969,1.583 0.344,0.167 10 false GND 3.625,0.99 4.115,1.177 0.49,0.188 10 false +BWP 5.479,1.51 5.927,1.677 0.448,0.167 10 false NIWP 5.479,2.99 5.927,3.156 0.448,0.167 10 false MREL 5.115,1.021 5.385,1.198 0.271,0.177 10 false A38 5.115,1.469 5.385,1.646 0.271,0.177 10 false A38 5.115,3 5.385,3.177 0.271,0.177 10 false A39 5.167,0.802 5.365,0.979 0.198,0.177 10 false 13 5.167,1.25 5.365,1.427 0.198,0.177 10 false 14 5.198,2.771 5.333,2.948 0.135,0.177 10 false 6 5.344,3.958 6.646,4.323 1.302,0.365 10 false Power Management Control ECU 4.75,0.875 4.885,1.052 0.135,0.177 10 false 3 4.75,1.323 4.885,1.5 0.135,0.177 10 false 2 3.458,0.875 3.594,1.052 0.135,0.177 10 false 4 1.063,0.885 1.198,1.063 0.135,0.177 10 false 2 0.729,0.885 0.865,1.063 0.135,0.177 10 false 1 1.354,0.906 1.49,1.083 0.135,0.177 10 false 5 2.115,1.292 2.25,1.469 0.135,0.177 10 false 1 2.146,0.917 2.281,1.094 0.135,0.177 10 false 3 1.344,1.271 1.479,1.448 0.135,0.177 10 false 2 3.458,1.323 3.594,1.5 0.135,0.177 10 false 1 3.677,1.927 4.781,2.302 1.104,0.375 10 false Inverter Water Pump Assembly 3.677,1.76 4.021,1.927 0.344,0.167 10 false A50 2.115,2.49 2.25,2.667 0.135,0.177 10 false 5 2.115,2.875 2.25,3.052 0.135,0.177 10 false 1 1.365,2.51 1.5,2.688 0.135,0.177 10 false 3 1.354,2.854 1.49,3.031 0.135,0.177 10 false 2 0.417,1.208 1.198,1.396 0.781,0.188 10 false INV W/PMP 1.396,1.76 2.177,1.948 0.781,0.188 10 false INV W/PMP 2.667,1.906 3.448,2.365 0.781,0.458 10 false INV W/PMP RLY 5.5,3.5 5.844,3.667 0.344,0.167 10 false E1 5.208,3.281 5.344,3.458 0.135,0.177 10 false 6 5.177,3.479 5.365,3.656 0.188,0.177 12 false I3 2.438,1.833 2.573,2.01 0.135,0.177 10 false 2 2.448,2.146 2.583,2.323 0.135,0.177 10 false 1 0.323,4.031 3.219,4.229 2.896,0.198 10 false IWP: Inverter water pump assembly drive duty 0.323,4.396 3.708,4.615 3.385,0.219 10 false NIWP: Inverter water pump assembly speed signal

CAUTION / NOTICE / HINT

NOTICE:

If DTC P0A78-284, 286, P0A7A-322, 324, P0A94-553 or 557 is output, replace the inverter with converter assembly after this inspection.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 120 seconds or more (when the power switch is turned on (READY), the inverter water pump assembly operates).



PROCEDURE

1.CHECK QUANTITY OF HV COOLANT

A

2.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR HV COOLANT LEAK
NOTICE:

In the case of a coolant leak, the inverter water pump assembly activates a fail-safe function. If the inverter water pump assembly is not the cause of the coolant leak, it is not necessary to replace it.



2.CHECK COOLANT HOSE

OK

3.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NG

CORRECT THE PROBLEM

3.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:
·

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

·

When the inverter water pump assembly serial communication line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter W/P Revolution.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter W/P Revolution
50003 236 615

d.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 625 rpm or less


HINT:

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.



e.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
4.CLEAR DTC

NEXT

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Water Pump
50004 236 9

d.

Select Inverter W/P Revolution in the Data List.


e.

While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter W/P Revolution
50003 236 615
Result:
Data List Item Specified Condition
Inverter W/P Revolution 2500 to 5875 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.




f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

A

B

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A259382

Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG




OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Disconnect connector A50 from the inverter water pump assembly.


c.

Measure the resistance according to the value(s) in the table below.

A260030C08
1.813,1.719 2.146,1.917 0.333,0.198 5.938,1.406 6.271,1.604 0.333,0.198 1.396,1.865 1.771,2.219 true 5.344,1.542 5.292,1.917 true 1.833,2.167 2.156,2.354 0.323,0.188 10 false IWP 5.104,1.948 5.5,2.135 0.396,0.188 10 false SWP 0.417,0.229 0.615,0.417 0.198,0.188 10 false *a 4.385,0.229 4.583,0.417 0.198,0.188 10 false *b 1.854,1.74 2.125,1.906 0.271,0.167 10 false A38 5.979,1.427 6.25,1.594 0.271,0.167 10 false A50
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A50-3 (SWP) - A38-13 (IWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A50-3 (SWP) or A38-13 (IWP) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the power management control ECU connector.


e.

Connect the inverter water pump assembly connector.

Result:
Proceed to
OK
NG




OK

10.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Remove the INV W/PMP fuse from the No. 2 engine room relay block.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter W/P Revolution
50003 236 615

e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 125 rpm or less



f.

Turn the power switch off.


g.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Turn the power switch on (IG).


c.
A204443C39
0.635,2.969 1.052,3.208 0.417,0.24 1.823,0.635 2.24,0.875 0.417,0.24 1.99,2.156 1.823,1.396 false 0.781,2.427 1.323,2.26 false 0.104,0.083 0.375,0.292 0.271,0.208 10 false *a 1.906,2.188 2.396,2.354 0.49,0.167 10 false E1 1.396,2.188 1.875,2.354 0.479,0.167 10 false IWP 1.969,0.667 2.552,0.906 0.583,0.24 10 false I3 0.708,3.01 1.042,3.177 0.333,0.167 10 false A38
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-13 (IWP) - I3-6 (E1) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

12.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

NG

12.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Turn the power switch on (IG).


b.
A249750C10
0.594,0.938 1.01,1.177 0.417,0.24 1.865,0.938 2.281,1.177 0.417,0.24 0.771,1.771 0.76,2.396 false 1.823,1.708 1.865,2.385 false 0.656,0.979 1.063,1.198 0.406,0.219 10 false A38 0.177,0.156 0.448,0.323 0.271,0.167 10 false *a 1.802,2.427 2.198,2.74 0.396,0.313 10 false E1 0.667,2.438 1.083,2.698 0.417,0.26 10 false IWP 2.021,0.99 2.427,1.208 0.406,0.219 10 false I3
*a Component with harness connected
(Power Management Control ECU)


While turning the power switch on (IG), check the waveform between the power management control ECU terminals.

Item Content
Terminal A38-13 (IWP) - I3-6 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Power switch on (IG)

OK:

Waveform duty ratio is between 3% and 9%.



c.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

NG