Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-803  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3004-803 High Voltage Power Resource One of the following occurs while the power switch is on (READY):
·

Electric battery fuse in the service plug grip has an open circuit

·

Service plug grip is not installed

·

SMRB remains open

·

SMRG remains open

·

High voltage cable has an open circuit


·

Hybrid battery junction block assembly

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P3004-803 only is output. A
Any of the following DTCs are also output. B
P0A95-123 is also output. C



DTC No. Relevant Diagnosis
P0A1A-151, 155, 156, 658, 659 Generator Control Module
P0A1B-164, 193, 512, 661, 786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0A78-266, 267, 586 Drive Motor "A" Inverter Performance
P0A94-442 DC/DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
P3004-131, 132 High Voltage Power Resource
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P3004-803 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



e.

Turn the power switch off.



A

2.CLEAR DTC

B

C

2.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read and record the DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 236

e.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Ensure the safety of the areas in front and at the back of the vehicle.


d.

Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.

HINT:
·

Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.

·

Depressing both the accelerator pedal and brake pedal at the same time causes Accelerator and brake depressing in the inappropriate operation and history data to be counted.




e.

Enter the following menus: Powertrain / Hybrid Control / DTC.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P3004-803 is output, or no DTCs are output. A
Power switch is not turned on (READY) and P3004- 131 is output. B


HINT:

Because P3004-131 uses 2-trip detection logic, the DTC detection conditions need to be met 2 times.



g.

Turn the power switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

B

4.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector I3 from the power management control ECU.


c.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.
A284482C35
1.885,2.365 2.25,2.573 0.365,0.208 1.552,3.51 1.865,3.74 0.313,0.229 2.021,1.781 1.552,1.781 false 2.198,3.688 2.708,4.406 false 2.625,1.781 2.156,1.781 false 2.063,3.688 1.677,4.406 false 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.073,2.531 0.385,2.688 0.313,0.156 10 false *b 1.115,1.708 1.729,1.906 0.615,0.198 10 false SMRB 2.771,4.344 3.219,4.552 0.448,0.208 10 false SMRB 1.979,2.396 2.594,2.698 0.615,0.302 10 false I3 1.594,3.552 1.906,3.75 0.313,0.198 10 false O9 2.667,1.708 3.281,1.906 0.615,0.198 10 false SMRG 1.198,4.344 1.646,4.552 0.448,0.208 10 false SMRG
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


Disconnect connector O9 from the hybrid battery junction block assembly.

HINT:

Before disconnecting the connector, check whether it is connected securely to the hybrid battery junction block assembly.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-4 (SMRB) - O9-1 (SMRB) Power switch off Below 1 Ω
I3-2 (SMRG) - O9-3 (SMRG) Power switch off Below 1 Ω



f.

Connect hybrid battery junction block assembly connector.


g.

Install the No. 4 hybrid battery shield panel.


h.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR