Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P3107-214 | Lost Communication with Airbag System Control Module | Open or short to +B in the communication circuit | ·
Wire harness or connector ·
Airbag sensor assembly ·
Power management control ECU |
Does not come on | Master Warning Light:
Comes on |
Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).
Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / SRS Airbag / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. | B |
Turn the power switch off.
A
B
(Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213)
| Proceed to |
|---|
| A |
| B |
A
B
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A09-591)
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P3107-214 is not output. | A |
| P3107-214 is output again. | B |
Turn the power switch off.
A
B
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Airbag Sensor Assembly) |
Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 Fuse |
Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.
| *a | Component without harness connected
(Airbag Sensor Assembly) |
Disconnect connector I47 from the airbag sensor assembly.
| *a | Component with harness connected
(Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-29 (ABFS) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
Connect the airbag sensor assembly connector.
Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector I3 from the power management control ECU.
Disconnect connector I47 from the airbag sensor assembly.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
| *b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-29 (ABFS) - I47-14 (GSW2) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-29 (ABFS) or I47-14 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.
Connect the airbag sensor assembly connector.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Component without harness connected
(Airbag Sensor Assembly) |
Disconnect connector I47 from the airbag sensor assembly.
Turn the power switch on (IG).
| *1 | Component with harness connected
(Power Management Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-29 (ABFS) - Body ground | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Connect the airbag sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
(Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS)
NG
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 Fuse |
Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.
| *a | Component without harness connected
(Airbag Sensor Assembly) |
Disconnect connector I47 from the airbag sensor assembly.
Disconnect all the connectors from the power management control ECU.
| *a | Rear view of wire harness connected
(Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-29 (ABFS) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connectors.
Connect the airbag ECU assembly connector.
Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG