Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AC0-123  Hybrid Battery Pack Current Sensor Circuit Range / Performance  


DESCRIPTION

Refer to the description for DTC P0ABF-123.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF-123

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance When the battery current sensor is abnormal (1 or 2 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit


Comes on Master Warning Light:
Comes on

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check for and record HV system DTCs, INF codes and freeze frame data.


e.

Read the output DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
Only DTC P0AC0-123 is output or DTC P0AC0-123 and DTCs other than those in the following table are output. A
Any of the DTCs in the following table are output at the same time. B


Relevant DTC
P0A95-123 High Voltage Fuse
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123, P0B42-123, P0B47-123, P0B4C-123, P0B51-123, P0B56-123, P0B5B-123, P0B60-123, P0B65-123, P0B6A-123, P0B6F-123, P0B74-123, P0B79-123, P0B7E-123, P0B83-123, P0B88-123, P0B8D-123, P0B92-123 Hybrid Battery Voltage Sensor "A - R" Circuit Low


f.

Turn the power switch off.


g.

Disconnect the intelligent tester from the DLC3.



A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).

NOTICE:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol -V01 to V17.

Powertrain > Hybrid Control > Data List
Tester Display
Battery Block Vol -V01
Battery Block Vol -V02
Battery Block Vol -V03
Battery Block Vol -V04
Battery Block Vol -V05
Battery Block Vol -V06
Battery Block Vol -V07
Battery Block Vol -V08
Battery Block Vol -V09
Battery Block Vol -V10
Battery Block Vol -V11
Battery Block Vol -V12
Battery Block Vol -V13
Battery Block Vol -V14
Battery Block Vol -V15
Battery Block Vol -V16
Battery Block Vol -V17
50003 236 635,636,637,638,639,640,641,642,643,644,645,646,647,648,649,650,651
NOTICE:

Select "Battery Block Vol -V01 to V17" only. (Do not select any other Data List items.)



d.

Check the voltage of each "Battery Block Vol" of "Battery Block Vol -V01 to V17" in the Data List with the power switch on (IG).

A315508E05
0.052,2.26 5,2.5 4.948,0.24 10 false Example: The change in voltage of "Battery Block Vol -V02" is 0.3 V or more. 0.052,0.031 5.052,0.271 5,0.24 10 false Example: The change in voltage of "Battery Block Vol -V01" is less than 0.3 V. 0.135,1.24 1.219,1.583 1.083,0.344 10 false Less than 0.3 V 6.75,3.313 7.156,3.531 0.406,0.219 10 false 0.3 V 6.75,1.24 7.156,1.458 0.406,0.219 10 false 0.3 V 0.969,3.302 1.969,3.563 1,0.26 10 false 0.3 V or more 3.833,4.188 4.833,4.448 1,0.26 10 false 60 seconds 0.052,4.469 5.427,4.729 5.375,0.26 10 false NOTICE: Check the voltage of each other "Battery Block Vol" in the same manner.

Specified Condition:

Any "Battery Block Vol" changes by 0.3 V or more 60 seconds after the power switch is turned on (IG). (The difference between the maximum and minimum voltage is 0.3 V or more.)


Result:
Result Proceed to
The change in voltage of any "Battery Block Vol" is 0.3 V or more. A
Other than above B



e.

Turn the power switch off.


f.

Disconnect the intelligent tester from the DLC3.



A

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY