Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0ABF-123  Hybrid Battery Pack Current Sensor Circuit  P0AC1-123  Hybrid Battery Pack Current Sensor Circuit Low  P0AC2-123  Hybrid Battery Pack Current Sensor Circuit High  


DESCRIPTION

The battery current sensor, which is mounted on the positive cable side of the HV battery, detects the amperage that flows into the HV battery. The battery smart unit receives a voltage, which varies between 0 and 5 V in proportion to the amperage, at its IB terminal from the battery current sensor. An output voltage of the battery current sensor below 2.5 V indicates that the HV battery is being charged, and above 2.5 V indicates that the HV battery is being discharged. The power management control ECU determines the charging and discharging amperage of the HV battery based on the signals that are input to its IB terminal from the battery smart unit, and calculates the SOC (state of charge) of the HV battery through the accumulated amperage.

A260083E06
0.167,0.063 0.729,0.594 0.563,0.531 10 false Charging Current 1.073,0.063 1.833,0.656 0.76,0.594 10 false Discharging Current 1.125,1.083 2.104,1.635 0.979,0.552 10 false Battery Current Sensor 2.031,0.583 3.25,0.927 1.219,0.344 10 false Battery Smart Unit 2.375,1.563 2.635,1.74 0.26,0.177 10 false VIB 2.375,1.938 2.635,2.115 0.26,0.177 10 false GIB 2.375,1.74 2.542,1.917 0.167,0.177 10 false IB 3.917,0.948 4.146,1.115 0.229,0.167 10 false 4.5 3.917,1.688 4.146,1.854 0.229,0.167 10 false 2.5 3.917,2.417 4.146,2.583 0.229,0.167 10 false 0.5 4.219,2.719 4.521,2.875 0.302,0.156 10 false -200 6.698,2.719 6.958,2.875 0.26,0.156 10 false 200 5.552,2.719 5.667,2.875 0.115,0.156 10 false 0 4.896,3.271 6.333,3.458 1.438,0.188 10 false HV Battery Current (A) 3.479,0.219 5.885,0.552 2.406,0.333 10 false Battery Current Sensor Output Voltage 3.948,0.563 4.333,0.802 0.385,0.24 10 false (V) 4.188,3.135 4.802,3.375 0.615,0.24 10 false Charge 6.438,3.146 7.125,3.344 0.688,0.198 10 false Discharge

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit When the battery current sensor is abnormal (1 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low When the battery current sensor is abnormal (1 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High When the battery current sensor is abnormal (1 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A306383E10
1.875,1.01 2.135,1.271 0.26,0.26 10 false IB 2.115,0.948 2.375,1.208 0.26,0.26 10 false 3 2.115,1.573 2.375,1.833 0.26,0.26 10 false 1 2.125,2.198 2.375,2.448 0.25,0.25 10 false 2 1.813,2.281 2.115,2.698 0.302,0.417 10 false GIB 1.802,1.646 2.083,2.031 0.281,0.385 10 false VIB 5.156,1.031 5.438,1.417 0.281,0.385 10 false IB 5.146,1.688 5.427,2.073 0.281,0.385 10 false VIB 5.146,2.323 5.448,2.74 0.302,0.417 10 false GIB 4.875,2.229 5.094,2.563 0.219,0.333 10 false 12 4.927,1.594 5.094,1.906 0.167,0.313 10 false 6 4.917,0.927 5.083,1.24 0.167,0.313 10 false 5 0.604,2.875 2.979,3.281 2.375,0.406 10 false Battery Current Sensor (Hybrid Battery Junction Block Assembly) 0.375,2.833 0.615,3.083 0.24,0.25 10 false z9 4.948,2.854 5.188,3.104 0.24,0.25 10 false z8 5.156,2.865 6.333,3.26 1.177,0.396 10 false Battery Smart Unit

Refer to the wiring diagram for DTC U029A-123.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>U029A-123

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)

B

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)

OK

3.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)
NOTICE:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.

Disconnect connector z8 from the battery smart unit.


e.
A259430E02
1.823,1.135 2.177,1.354 0.354,0.219 1.854,1.156 2.156,1.344 0.302,0.188 10 true z9

A260183C18
0.594,1.542 1.021,1.802 0.427,0.26 0.573,3.563 1,3.823 0.427,0.26 1.583,1.656 2.396,1.167 true 1.99,3.833 2.604,3.781 true 1.479,1.656 1.844,0.99 true 1.531,3.844 0.917,3.188 true 1.448,1.854 1.063,2.156 true 1.76,3.74 2.417,3.177 true 1.073,1.125 1.302,1.323 0.229,0.198 10 false *a 1.115,2.802 1.344,3 0.229,0.198 10 false *b 2.448,1.083 2.677,1.333 0.229,0.25 10 false IB 2.656,3.698 2.917,3.958 0.26,0.26 10 false IB 1.906,0.896 2.208,1.135 0.302,0.24 10 false VIB 0.677,3.083 0.969,3.365 0.292,0.281 10 false VIB 0.792,2.094 1.083,2.292 0.292,0.198 10 false GIB 2.458,3.083 2.792,3.354 0.333,0.271 10 false GIB 0.719,1.594 0.917,1.74 0.198,0.146 10 false z8 0.698,3.594 0.927,3.74 0.229,0.146 10 false z9
*a Rear view of wire harness connector
(to Battery Smart Unit)
*b Front view of wire harness connector
(to Hybrid Battery Junction Block)


Disconnect the z9 battery current sensor connector from the hybrid battery junction block assembly.


f.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
z8-5 (IB) - z9-3 (IB) Power switch off Below 1 Ω
z8-12 (GIB) - z9-2 (GIB) Power switch off Below 1 Ω
z8-6 (VIB) - z9-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
z8-5 (IB) or z9-3 (IB) - Body ground and other terminals Power switch off 10 kΩ or higher
z8-12 (GIB) or z9-2 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z8-6 (VIB) or z9-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



HINT:

Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.


g.

Connect the battery smart unit connector.


h.

Connect the battery current sensor connector to the hybrid battery junction block assembly.


i.

Install the No. 4 hybrid battery shield panel.


j.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)
NOTICE:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A260172C07
0.917,0.073 1.344,0.333 0.427,0.26 0.583,0.458 0.917,0.896 true 0.906,0.979 0.615,1.729 true 0.063,0.073 0.292,0.271 0.229,0.198 10 false *a 0.344,0.313 0.594,0.552 0.25,0.24 10 false VIB 0.448,1.792 0.802,2.01 0.354,0.219 10 false GIB 1.052,0.104 1.281,0.313 0.229,0.208 10 false z8
*a Component with harness connected
(Battery Smart Unit)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z8-6 (VIB) - z8-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

5.CHECK BATTERY SMART UNIT (IB VOLTAGE)

NG

5.CHECK BATTERY SMART UNIT (IB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A260172C08
0.875,0.104 1.302,0.365 0.427,0.26 0.99,0.875 1.781,0.344 true 0.906,0.979 0.615,1.729 true 0.104,0.063 0.313,0.323 0.208,0.26 10 false *a 1.823,0.219 2.073,0.458 0.25,0.24 10 false IB 0.479,1.76 0.781,2.042 0.302,0.281 10 false GIB 1.01,0.135 1.229,0.333 0.219,0.198 10 false z8
*a Component with harness connected
(Battery Smart Unit)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z8-5 (IB) - z8-12 (GIB) Power switch on (IG) 2.46 to 2.54 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY