The speed of the battery cooling blower assembly is controlled by the power management control ECU. Power is supplied to the battery cooling blower assembly when the MREL terminal of the power management control ECU turns on the IGCT relay. The power management control ECU sends command signals (SI) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The battery cooling blower assembly frequency (FP) is sent to the power management control ECU via the battery smart unit as a monitor signal using serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A84-123 | Hybrid Battery Pack Cooling Fan 1 Control Circuit Low | When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target control speed range (1 trip detection) | ·
Wire harness or connector ·
BATT FAN fuse ·
Battery cooling blower assembly ·
Battery smart unit ·
Power management control ECU |
Does not come on | Master Warning Light:
Comes on |
Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A7F-123
| Proceed to |
|---|
| A |
| B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
| Tester Display |
|---|
| Driving the Battery Cooling Fan |
Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
Check that the fan operates and air is sucked into the inlet duct.
The cooling fan may not stop even when turning the cooling fan off in the "Driving the Battery Cooling Fan" Active Test. This is due to HV system control and not a malfunction.
The fan operates.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Remove the rear side seat back assembly LH.
Disconnect connector r1 from the battery cooling blower assembly.
Disconnect connector N18 from the battery smart unit.
| *1 | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *2 | Rear view of wire harness connector
(to Battery Smart Unit) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r1-2 (FP0) - N18-5 (FP0) | Power switch off | Below 1 Ω |
| r1-2 (FP0) or N18-5 (FP0) - Body ground | Power switch off | 10 kΩ or higher |
Connect the battery cooling blower assembly connector.
Connect the battery smart unit connector.
Install the rear side seat back assembly LH.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.
If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
When DTCs are cleared, freeze frame data and INF codes are also cleared.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
| Tester Display |
|---|
| Driving the Battery Cooling Fan |
If the Active Test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
Enter the following menus: Powertrain / Hybrid Control / Data List / Cooling Fan Frequency1.
| Tester Display |
|---|
| Cooling Fan Frequency1 |
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Rear view of battery cooling blower assembly connector
(to Wire Harness Connector) |
While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.
| Tester Connection | Condition |
|---|---|
| r1-2 (FP0) - r1-4 (GND0) | Battery cooling blower assembly is operating |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.
| Result | Proceed to |
|---|---|
| The value in the Data List (Cooling Fan Frequency1) and the actual measured value at the battery cooling blower assembly connector are 0 Hz. | A |
| Other than above | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the luggage compartment front trim cover.
A
B
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Disconnect the r1 battery cooling blower assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR
| *a | Rear view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r1-2 (FP0) - r1-4 (GND0) | Power switch on (IG) | 4.5 to 5.5 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the r1 battery cooling blower assembly connector.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A82-123
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the BATT FAN fuse from the No. 2 engine room relay block.
| *1 | No. 2 Engine Room Relay Block |
| *2 | BATT FAN Fuse |
Measure the resistance of the BATT FAN fuse.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BATT FAN fuse | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
When DTCs are cleared, freeze frame data and INF codes are also cleared.
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r1-1 (IG0) - Body ground | Battery cooling blower is operating | 11 to 14 V |
Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Measure the voltage on the wire side of the connector that is part of the battery cooling blower.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Disconnect connector r1 from the battery cooling blower assembly.
Disconnect connector A38 from the power management control ECU.
Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r1-3 (SI0) - A38-29 (SI0) | Power switch off | Below 1 Ω |
| r1-3 (SI0) or A38-29 (SI0) - Body ground | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r1-3 (SI0) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the battery cooling blower assembly connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Connect the battery cooling blower assembly connector.
Install the luggage compartment front trim cover.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
When DTCs are cleared, freeze frame data and INF codes are also cleared.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
| Tester Display |
|---|
| Driving the Battery Cooling Fan |
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Cooling Blower Assembly) |
Connect an oscilloscope to the r1 battery cooling blower assembly connector and check the waveform.
| Item | Content |
|---|---|
| Tester Connection | r1-3 (SI0) - r1-4(GND0) |
| Equipment Setting | 10 V/DIV., 1 ms/DIV. |
| Condition | Power switch on (IG) during Active Test |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Perform this inspection with the battery cooling blower assembly connector connected.
The wave length will vary with the operating speed of the battery cooling blower assembly.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Waveform 1 |
Install the luggage compartment front trim cover.
| Result | Proceed to |
|---|---|
| Normal (The pulse output of waveform 1) | A |
| No pulse generation | B |
A
B
Disconnect connector I3 from the power management control ECU.
Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-5 (E01) - Body ground | Power switch off | Below 1 Ω |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector I4 from the power management control ECU.
Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I4-5 (E02) - Body ground | Power switch off | Below 1 Ω |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGCT relay from the No. 2 engine room relay block.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Disconnect connector r1 from the battery cooling blower assembly.
| *1 | No. 2 Engine Room Relay Block |
| *2 | IGCT Relay block |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (IGCT relay block) - r1-1 (IG0) | Power switch off | Below 1 Ω |
Install the IGCT relay.
Connect the battery cooling blower assembly connector.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the BATT FAN fuse from the No. 2 engine room relay block.
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Disconnect connector r1 from the battery cooling blower assembly.
| *1 | No. 2 Engine Room Relay Block |
| *2 | BATT FAN fuse block |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r1-1 (IG0) - Terminals other than 2 (BATT FAN fuse block) and body ground | Power switch off | 10 kΩ or higher |
Install the BATT FAN fuse.
Connect the battery cooling blower assembly connector.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the luggage compartment front trim cover.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL
Disconnect connector r1 from the battery cooling blower assembly.
| *a | Component without harness connected
(Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r1-1 (IG0) - r1-4 (GND0) and body ground | Power switch off | 10 kΩ or higher |
Connect the battery cooling blower assembly connector.
Install the luggage compartment front trim cover.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT