Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › CYLINDER HEAD
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074907 CYLINDER HEAD G

2AR-FXE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifold.

A284093C09
4.083,0.198 4.396,0.354 0.313,0.156 10 *a 4.083,1.75 4.396,1.906 0.313,0.156 10 *b 4.083,2.708 4.396,2.865 0.313,0.156 10 *c
*a Cylinder Head Lower Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Maximum Warpage:
Item Specified Condition
Cylinder head lower side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head.


b.
A194969

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.

If cracked, replace the cylinder head.


Hide 13711B 2.INSPECT COMPRESSION SPRING

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.

A361727C02
0.292,0.063 3.406,3.76 3.115,3.698 3.792,0.063 6.906,3.76 3.115,3.698 2.354,0.594 3.063,0.594 false 5.823,0.604 6.531,0.604 false 1.969,0.927 2.677,0.927 false 5.375,0.938 6.083,0.938 false 1.958,2.021 2.667,2.021 false 5.406,1.938 6.115,1.938 false 1.844,3.052 2.552,3.052 false 5.292,3.042 6,3.042 false 0.375,0.135 0.708,0.344 0.333,0.208 12 false *A 3.896,0.146 4.396,0.479 0.5,0.333 12 false *B 3.125,0.531 3.438,0.688 0.313,0.156 10 false *1 2.719,0.854 3.031,1.01 0.313,0.156 10 false *2 2.719,1.958 3.031,2.115 0.313,0.156 10 false *3 2.594,2.99 2.906,3.146 0.313,0.156 10 false *4 6.125,0.865 6.438,1.021 0.313,0.156 10 false *2 6.573,0.531 6.885,0.688 0.313,0.156 10 false *1 6.167,1.865 6.479,2.021 0.313,0.156 10 false *3 6.042,2.969 6.354,3.125 0.313,0.156 10 false *4
*A Type A
(Compression Spring Shape: Straight)
*B Type B
(Compression Spring Shape: Tapered)
*1 No. 1 Valve Rocker Arm Sub-assembly *2 Valve Spring Retainer
*3 Compression Spring *4 Valve Lash Adjuster Assembly



a.
A194990

Type A:

i.

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:
Wire Diameter Specified Condition
3.3 mm (0.130 in.) 49.0 to 51.0 mm (1.93 to 2.01 in.)
3.4 mm (0.134 in.) 47.2 to 49.2 mm (1.86 to 1.94 in.)


If the free length is not as specified, replace the compression spring.


ii.
A194991C07
1.449,0.144 1.67,0.309 0.221,0.166 10 *a
*a Deviation


Using a steel square, measure the deviation of the compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle:

2°


If the deviation is more than the maximum, replace the compression spring.



b.

Type B:

i.
A333833

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

47.38 mm (1.87 in.)


If the free length is not as specified, replace the compression spring.


ii.
A335450C03
2.292,1.271 2.49,1.49 0.198,0.219 10 false *b 1.208,0.115 1.406,0.302 0.198,0.188 10 false *a
*a Deviation
*b 30 mm (1.18 in.)


Using a steel square, measure the deviation of the compression spring at the position shown in the illustration.

Maximum deviation:

1.0 mm (0.0394 in.)


If the deviation is more than the maximum, replace the compression spring.



Hide 13711 3.INSPECT INTAKE VALVE

a.
A194992

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.21535 to 0.21594 in.)



b.
A194993C10
0.539,1.54 1.677,1.715 1.138,0.175 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


c.
A194994C09
2.192,1.055 3.177,1.207 0.985,0.152 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard overall length:

103.92 mm (4.09 in.)


Minimum overall length:

103.42 mm (4.07 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.
A194995

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.465 mm to 5.480 mm (0.21516 to 0.21575 in.)



b.
A194996C12
0.541,1.541 0.76,1.712 0.219,0.171 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


c.
A194997C09
2.321,0.989 2.612,1.173 0.291,0.184 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard overall length:

112.91 mm (4.44 in.)


Minimum overall length:

112.41 mm (4.43 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 11122 5.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A194967

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

5.510 to 5.530 mm (0.2169 to 0.2177 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and guide bush.


Hide 11131 6.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.
A194998C12
1.692,1.719 2.107,1.889 0.416,0.17 10 *a
*a Width


Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 11135 7.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.
A194999C08
1.508,1.731 1.924,1.897 0.416,0.166 10 *a
*a Width


Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 13511 8.INSPECT CAMSHAFT OIL CLEARANCE

NOTICE:

Do not turn the camshafts.


a.

Clean the bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A259165C02
1.333,0.802 0.979,0.083 0.979,0.083 0.885,0.083 false 0.688,0 0.906,0.177 0.219,0.177 10 false *1
*1 Plastigage


Lay a strip of Plastigage across each of the camshaft journals.



e.

Install the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>CYLINDER HEAD GASKET>INSTALLATION



g.
A259166C02
1.354,1.01 1.01,0.302 1.01,0.302 0.917,0.302 true 0.49,3.167 0.979,2.375 0.979,2.375 0.479,3.823 true 1.063,3.865 1.885,4.427 1.885,4.427 2.802,3.865 false 1.052,3.188 1.885,4.427 1.885,4.427 2.771,3.188 false 1.646,3.188 1.885,4.427 1.885,4.427 2.219,3.188 false 1.646,3.865 1.885,4.427 1.885,4.427 2.24,3.865 false 0.719,0.229 1.01,0.479 0.292,0.25 10 false *1 1.01,2.281 1.198,2.458 0.188,0.177 10 false *2 1.823,4.469 2.094,4.646 0.271,0.177 10 false *3
*1 Plastigage
*2 No. 1 Journal
*3 Other Journal


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.035 to 0.072 mm (0.00137 to 0.00283 in.)
Exhaust No. 1 journal 0.005 to 0.054 mm (0.000197 to 0.00213 in.)
Other journal 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.085 mm (0.00335 in.)
Exhaust No. 1 journal 0.085 mm (0.00335 in.)
Other journal 0.085 mm (0.00335 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.


Hide 13511 9.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Clean the bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.



d.

Install the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>CYLINDER HEAD GASKET>INSTALLATION


e.
A259167

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard Thrust Clearance:
Item Specified Condition
Intake 0.060 to 0.155 mm (0.00236 to 0.00610 in.)
Exhaust 0.060 to 0.155 mm (0.00236 to 0.00610 in.)


Maximum Thrust Clearance:
Item Specified Condition
Intake 0.170 mm (0.00669 in.)
Exhaust 0.170 mm (0.00669 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.