Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2012.02–2013.07
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074902 CYLINDER HEAD GASKET A

2AR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD BOLT

Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 3.INSTALL CYLINDER HEAD GASKET

a.
A259153
2.135,0.813 2.188,0.49 2.188,0.49 2.25,0.49 true 2.448,2.969 2.167,2.969 false 0.677,3.573 0.385,3.979 0.385,3.979 0.385,4.052 false 2.292,0.406 2.615,0.708 0.323,0.302 10 false *a 2.24,4.292 3.052,4.615 0.813,0.323 10 false 7.0 mm 0.615,2.76 2.052,3.094 1.438,0.333 10 false 3.0 to 7.0 mm 0.302,4.052 0.604,4.302 0.302,0.25 10 false *1 0.708,3.865 1.083,4.188 0.375,0.323 10 false *2 1.74,3.396 1.927,3.625 0.188,0.229 10 false *c 1.99,2.896 2.167,3.083 0.177,0.188 10 false *2 0.198,3.365 0.542,3.729 0.344,0.365 10 false *b
*1 Cylinder Head Gasket
*2 Cylinder Block
*a Lot No.
*b 3.0 mm or more
*c 20 mm or more
V100135

Seal Packing
V100136

Front


Clean the cylinder block and cylinder head with solvent.


b.

Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal dimension:

3.0 to 7.0 mm (0.118 to 0.276 in.) wide and 3.0 mm (0.118 in.) thick


HINT:

Apply at least 20 mm (0.787 in.) of seal packing from the inside edge of the protrusion of the cylinder block.


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.

Place a new cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp facing upward.

NOTICE:

Pay attention to the installation direction.



Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head bolts are tightened in 4 progressive steps.


a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Ensure that no oil is on the mounting surface of the cylinder head.

·

Place the cylinder head on the cylinder block gently in order not to damage the gasket with the bottom part of the head.




b.

Install the plate washers to the cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
A196908N13
2.417,0.281 2.521,0.427 0.104,0.146 10 false 9 1.5,1.646 1.594,1.802 0.094,0.156 10 true 1 1.49,0.24 1.583,0.417 0.094,0.177 10 false 2 1.958,1.635 2.073,1.781 0.115,0.146 10 true 3 1.031,0.281 1.125,0.438 0.094,0.156 10 false 4 1.948,0.281 2.063,0.427 0.115,0.146 10 false 5 1.021,1.625 1.135,1.781 0.115,0.156 10 true 6 2.438,1.635 2.563,1.792 0.125,0.156 10 true 7 0.615,0.281 0.708,0.427 0.094,0.146 10 false 8 0.5,1.646 0.677,1.792 0.177,0.146 10 true 10

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the plate washer for the cylinder head bolt into the cylinder head.




e.

Step 2:

i.

Tighten the cylinder head bolts again in the sequence shown in the illustration to make sure that they are tightened to the specified torque.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



f.

Step 3:

i.
A196910
1.098,1.567 1.28,1.751 0.181,0.184 10 *a 0.896,0.378 1.195,0.539 0.3,0.161 10 90° 2.585,0.378 2.885,0.539 0.3,0.161 10 90° 1.239,1.567 1.497,1.156 false
*a Painted Mark
V100136

Front


Mark each cylinder head bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



g.

Step 4:

i.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.


ii.

Check that the paint marks are now facing rearward.

NOTICE:
·

Do not apply oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.



HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13716 5.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.

Install the 16 valve stem caps to the cylinder head.

NOTICE:

Do not drop the valve stem caps into the cylinder head.



Hide 13050 6.SET CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

When installing the camshaft timing gear, release the lock pin and set the camshaft timing gear to the advanced position before installation.


a.
A284096C17
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 false 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 false 2.042,1.604 2.458,1.948 2.458,1.948 2.615,1.948 false 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 false 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 0.083,2.583 0.396,2.74 0.313,0.156 10 false *b 0.708,1.625 1.021,1.781 0.313,0.156 10 false *1 2.667,1.844 2.979,2 0.313,0.156 10 false *c 2.635,3.323 2.948,3.479 0.313,0.156 10 false *c 0.604,3.854 0.917,4.01 0.313,0.156 10 false *1
*1 Knock Pin Hole
*a Advanced Position
*b Retarded Position
*c Alignment Mark


Check the camshaft timing gear position.

NOTICE:

If the camshaft timing gear is set to the advanced position, do not let the camshaft timing gear rotate clockwise during installation.

If the camshaft timing gear rotates to the retarded position, release the lock pin and set the camshaft timing gear to the advanced position.



b.
A196901
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 false 1.292,0.115 1.5,0.323 0.208,0.208 10 false *1 2.021,0.542 2.281,0.729 0.26,0.188 10 false *2
*1 Pin Hole
*2 Knock Pin


Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.


c.
A196904C59
2.167,0.844 1.917,0.844 1.917,0.844 1.49,1.083 false 0.823,0.729 0.917,0.729 0.917,0.729 1.156,0.979 false 0.604,0.646 0.781,0.802 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear
*2 Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


d.

Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



e.

Release the lock pin.

A284097
1.417,1.052 1.771,1.052 1.771,1.052 1.917,1.104 false 2.344,1.229 2.479,1.125 2.479,1.125 2.781,1.125 false 2.552,2.552 2.688,2.448 2.688,2.448 2.917,2.448 false 2.115,2.792 2.281,2.958 2.281,2.958 2.906,2.958 false 1.344,2.552 1.635,2.552 1.635,2.552 1.771,2.427 false 4.813,1.156 5.073,1.156 5.073,1.156 5.323,1.604 false 4.615,1.51 4.76,1.51 4.76,1.51 5.094,1.76 false 4.615,2.521 4.813,2.521 4.813,2.521 5.125,2.135 false 5.604,1.771 5.948,1.448 5.948,1.448 6.146,1.448 false 5.552,2.167 5.885,2.469 5.885,2.469 6.094,2.469 false 2.958,2.354 3.271,2.51 0.313,0.156 10 false *1 2.958,2.865 3.271,3.021 0.313,0.156 10 false *2 4.615,1.073 4.927,1.229 0.313,0.156 10 false *3 1.229,0.948 1.542,1.104 0.313,0.156 10 false *a 2.844,1.031 3.156,1.188 0.313,0.156 10 false *b 4.438,1.406 4.75,1.563 0.313,0.156 10 false *c 4.448,2.417 4.76,2.573 0.313,0.156 10 false *d 6.135,2.365 6.448,2.521 0.313,0.156 10 false *d 6.188,1.344 6.5,1.5 0.313,0.156 10 false *d 1.198,2.469 1.51,2.625 0.313,0.156 10 false A
*1 Rubber *2 Vinyl Tape
*3 Knock Pin - -
*a Retard Side Path *b Advance Side Path
*c Open *d Close


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug three of the paths with pieces of rubber.



iii.

Open a hole at port A shown in the illustration.


iv.
A196906

While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.


NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.


HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




v.

Remove the vinyl tape and rubber pieces from the camshaft.



f.

Remove the bolt and camshaft timing gear.

NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.



Hide 13750 7.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the valve lash adjuster before installing it.

Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


b.

Install the 16 lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster to the same place it was removed from.



Hide 13801 8.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A196911
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 Valve Rocker Arm
*2 Valve Lash Adjuster
*3 Valve Stem Cap


Apply engine oil to the lash adjuster tips and valve stem caps.


b.

Install the 16 valve rocker arms as shown in the illustration.


Hide 11821 9.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 10.INSTALL NO. 1 CAMSHAFT BEARING

Hide 15678A 11.INSTALL OIL CONTROL VALVE FILTER

Hide 13511 12.INSTALL CAMSHAFT

a.

Clean the camshaft journals, camshaft housing and bearing caps.


b.

Apply a light coat of engine oil to the camshaft journal, camshaft housing and bearing caps.


c.

Install the camshaft and No. 2 camshafts to the camshaft housing.

HINT:

Perform "Inspection After Repair" after replacing the camshaft or No. 2 camshaft.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13.INSTALL CAMSHAFT BEARING CAP

a.
A259154N05
2.896,0.021 2.99,0.177 0.094,0.156 10 false 5 2.333,0.021 2.427,0.177 0.094,0.156 10 false 4 1.719,0.021 1.813,0.177 0.094,0.156 10 false 3 1.104,0.021 1.198,0.177 0.094,0.156 10 false 2

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


b.
A259149N09
1,0.177 1.323,0.469 0.323,0.292 10 false 6 1.573,0.177 1.833,0.448 0.26,0.271 10 false 2 2.156,0.177 2.469,0.438 0.313,0.26 10 false 4 2.688,0.177 2.958,0.417 0.271,0.24 10 false 8 2.99,1.521 3.229,1.792 0.24,0.271 10 false 7 2.458,1.521 2.729,1.781 0.271,0.26 10 false 3 1.896,1.521 2.177,1.906 0.281,0.385 10 false 1 1.313,1.521 1.531,1.813 0.219,0.292 10 false 5 0.021,1.781 0.396,2.104 0.375,0.323 10 false 11 0.125,0.958 0.406,1.354 0.281,0.396 10 false 9 0.073,0.271 0.406,0.573 0.333,0.302 10 false 10

Install the 11 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Make sure that the camshaft rotates smoothly after installing the bearing caps.



Hide 11103 14.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A186390
1.844,0.615 2.115,0.615 false 0.552,0.802 0.823,0.802 false 1.51,0.229 1.969,0.229 false 2,0.146 2.229,0.354 0.229,0.208 10 false *1 2.177,0.531 2.385,0.771 0.208,0.24 10 false *2 0.354,0.708 0.604,0.896 0.25,0.188 10 false *3 0.219,1.594 0.375,1.813 0.156,0.219 10 false *b 0.198,0 0.385,0.24 0.188,0.24 10 false *a
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster
*a INCORRECT
*b CORRECT


Check that the valve rocker arms are installed as shown in the illustration.


b.
A196898
1.417,1.448 1.25,1.75 1.25,1.75 1.25,1.875 true 0.948,1.906 1.865,2.104 0.917,0.198 10 false 3.0 to 4.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.




c.
A259156C05
1.125,1.208 1.76,1.833 1.76,1.833 2.354,1.198 true 1.688,1.854 1.844,2.01 0.156,0.156 10 false *1 0.906,0.313 1.063,0.469 0.156,0.156 10 false *a 2.292,0.281 2.448,0.438 0.156,0.156 10 false *b
*1 Knock Pin
*a Approximately 17°
*b Approximately 2°


Position the knock pin of the No. 1 and No. 2 camshafts as shown in the illustration.


d.
A259142N13
2.313,0.594 2.49,0.75 0.177,0.156 10 true 10 3.135,1.74 3.354,1.938 0.219,0.198 10 false 17 2.344,1.854 2.698,2.135 0.354,0.281 10 false 20 3.125,0.344 3.406,0.625 0.281,0.281 10 false 18 1,0.021 1.333,0.229 0.333,0.208 10 false 9 0.406,0 0.76,0.219 0.354,0.219 10 false 15 1.542,0.021 1.875,0.271 0.333,0.25 10 false 3 2.094,0.021 2.396,0.26 0.302,0.24 10 false 6 2.563,0.021 2.896,0.26 0.333,0.24 10 false 12 3.229,1.073 3.427,1.406 0.198,0.333 10 false 16 0.719,0.594 0.927,0.781 0.208,0.188 10 true 7 1.281,0.594 1.49,0.792 0.208,0.198 10 true 1 1.865,0.594 2.021,0.76 0.156,0.167 10 true 4 0.052,0.979 0.344,1.26 0.292,0.281 10 false 13 0.208,1.99 0.51,2.177 0.302,0.188 10 false 14 0.958,1.854 1.292,2.135 0.333,0.281 10 false 8 1.542,1.854 1.813,2.125 0.271,0.271 10 false 2 2.125,1.854 2.406,2.135 0.281,0.281 10 false 5 2.802,1.844 3.083,2.073 0.281,0.229 10 false 11 0.677,1.875 0.927,2.115 0.25,0.24 10 true 19

Install the camshaft housing, and then install the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Do not apply oil for at least 2 hours after the installation.

·

Do not start the engine for at least 2 hours after the installation.

·

Thoroughly wipe clean any seal packing.




Hide 13523 15.INSTALL CAMSHAFT TIMING SPROCKET

a.
A259409C03
1.978,0.246 2.131,0.399 0.153,0.154 10 *a 0.449,0.366 0.602,0.52 0.153,0.154 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, and install the camshaft timing sprocket with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head or spark plug tube with the wrench.



Hide 13050 16.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A284102
0.604,1.302 0.771,1.302 0.771,1.302 1.781,0.854 false 2.708,1.573 2.542,1.573 2.542,1.573 2.052,1.135 false 0.427,1.208 0.74,1.365 0.313,0.156 10 false *1 2.76,1.479 3.073,1.635 0.313,0.156 10 false *a
*1 Knock Pin Hole
*a Alignment Mark


Check the camshaft timing gear position.

If the camshaft timing gear is not set to the advanced position, release the lock pin and reset the camshaft timing gear (Refer to the "Set Camshaft Timing Gear Assembly" procedure").


b.
A196901
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 false 1.292,0.115 1.5,0.323 0.208,0.208 10 false *1 2.021,0.542 2.281,0.729 0.26,0.188 10 false *2
*1 Pin Hole
*2 Knock Pin


Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.


c.
A196904C56
2.167,0.854 1.917,0.854 1.917,0.854 1.5,1.083 false 0.823,0.75 0.917,0.75 0.917,0.75 1.146,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear
*2 Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


d.
A259408C04
1.927,0.314 2.08,0.468 0.153,0.154 10 *a 0.397,0.366 0.55,0.52 0.153,0.154 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 1 camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 17.ADD ENGINE OIL

a.
A259155

Add 50 cc (3.1 cu. in) of engine oil into the oil hole shown in the illustration.

NOTICE:
·

Oil must be added if the lash adjusters were removed.

·

Make sure that the low pressure chamber and oil paths of the lash adjusters are full of engine oil.




Hide 13561 18.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A259139N03
1.875,0.615 2.052,0.802 0.177,0.188 10 true 1 2.375,2 2.594,2.177 0.219,0.177 10 true 2

Install the chain vibration damper with the 2 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 19.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A260711N02
1.313,0.198 1.594,0.375 0.281,0.177 10 true 40°

Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.


c.
A259157C03
1.615,0.802 2.302,0.802 true 1.125,0.563 2.313,0.563 true 2.583,2.177 3.083,2.177 true 2.354,0.719 2.469,0.875 0.115,0.156 10 false A 2.354,0.479 2.5,0.635 0.146,0.156 10 false *a 3.125,2.094 3.385,2.396 0.26,0.302 10 false *a 1.073,1.625 1.396,1.854 0.323,0.229 10 false *b 2.521,1.49 2.781,1.76 0.26,0.271 10 false *c
*a Timing Mark
*b Approximately 7°
*c Approximately 32°


Check that the timing marks of the camshaft timing gears are as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 13506 20.INSTALL CHAIN SUB-ASSEMBLY

a.

Place the chain onto the camshaft timing gears and crankshaft timing sprocket.

HINT:
·

Make sure the mark plate of the chain faces away from the engine.

·

It is not necessary to install the chain to the teeth of the gears and sprocket.




b.
A259158C03
2.917,0.177 2.635,0.177 2.635,0.177 2,0.458 true 2.896,0.771 2.135,0.771 2.135,0.771 1.927,0.646 true 2.969,0.094 3.24,0.375 0.271,0.281 10 false *a 2.979,0.667 3.281,0.917 0.302,0.25 10 false *b
*a Mark Plate
*b Timing Mark


Align the mark plate (yellow or gold) of the chain with the timing mark of the camshaft timing sprocket and install the chain to the camshaft timing sprocket.


c.
A196872C13
0.927,1.115 1.042,1.115 1.042,1.115 1.302,1.198 true 1.833,0.448 1.729,0.448 1.729,0.448 1.521,1.219 true 1.844,0.354 2.104,0.583 0.26,0.229 10 true *b 0.729,1.031 0.979,1.26 0.25,0.229 10 true *a
*a Mark Plate
*b Timing Mark


Align the mark plate (pink or gold) of the chain with the timing mark of the crankshaft timing sprocket and install the chain to the crankshaft timing sprocket.


d.
A196873

Tie a string above the crankshaft timing sprocket so that the chain is secure.


e.
A259159C03
1.729,0.271 1.458,0.271 1.458,0.271 0.865,0.531 true 1.844,0.781 0.906,0.781 true 1.781,0.188 2.156,0.51 0.375,0.323 10 false *a 1.885,0.698 2.302,1.031 0.417,0.333 10 false *b
*a Mark Plate
*b Timing Mark


Using the hexagonal portion of the intake camshaft, rotate the intake camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing gear with the mark plate (yellow or gold) of the chain and install the chain to the camshaft timing gear.

HINT:

Hold the intake camshaft in place with a wrench until the chain tensioner is installed.



f.
A259160

Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain so that the chain tensioner slipper can be installed.

NOTICE:

Make sure the chain is secure.



Hide 13559 21.INSTALL CHAIN TENSIONER SLIPPER

a.
A259138

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 22.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196877

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the stopper plate.


Hide 13566B 23.INSTALL TIMING CHAIN GUIDE

a.
A259137

Install the timing chain guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 24.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A259136C05
6.26,1.042 6.719,1.042 true 3.448,5.719 4.74,5.719 true 0.708,2.219 0.844,2.219 0.844,2.219 1.01,2.677 true 1.365,2.135 1.5,2.135 1.5,2.135 1.708,2.917 true 0.958,0.333 1.438,0.656 0.479,0.323 10 false *a 6.188,0.448 6.729,0.75 0.542,0.302 10 false *b 6.781,0.938 7.104,1.26 0.323,0.323 10 false *c 4.802,5.646 5.271,5.969 0.469,0.323 10 false *d 0.531,2.125 0.979,2.625 0.448,0.5 10 false *c 1.229,2.052 1.615,2.531 0.385,0.479 10 false A
*a Approximately 7° *b Approximately 32°
*c Timing Mark *d Crankshaft pulley set key



b.

Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.

HINT:

"A" is not a timing mark.



c.

Remove the crankshaft pulley bolt.


Hide 23814B 25.INSTALL FUEL DELIVERY PIPE

Hide 25680 28.INSTALL EGR COOLER ASSEMBLY

Hide 25051 29.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 17167 33.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 16261G 34.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 22030 35.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 11302 36.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY