Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL PUMP
RM2040EQ _51 Engine / Hybrid System _014694 2AR-FXE FUEL _0074912 FUEL PUMP A

2AR-FXE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 58325E 7.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A218217

Remove the rear floor service hole cover.


b.

Disconnect the fuel pump connector.


Hide 77209B 8.DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY

a.
A218218C02
1.281,2.844 1.052,2.615 1.052,2.615 0.979,2.615 false 2.073,2.865 2.365,2.573 2.365,2.573 2.458,2.573 false 1.135,3.729 0.635,3.729 false 1.135,3.573 0.885,3.573 0.885,3.573 0.885,3.729 false 1.313,1.875 1.073,2.115 1.073,2.115 0.958,2.115 false 1.823,3.354 2.229,3.354 false 1.896,3.573 2.24,3.906 2.24,3.906 2.333,3.906 false 2.302,3.292 2.49,3.479 0.188,0.188 10 *1 2.521,2.51 2.719,2.688 0.198,0.177 10 *3 0.448,3.667 0.625,3.833 0.177,0.167 10 *4 2.385,3.844 2.583,4.021 0.198,0.177 10 *5 0.781,2.042 0.969,2.229 0.188,0.188 10 *1 0.76,2.542 0.948,2.729 0.188,0.188 10 *2
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 Fuel Pump Tube
*4 O-ring
*5 Fuel Suction Plate


Remove the tube joint clip, and pull out the fuel pump tube.

NOTICE:
·

Remove any dirt or foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube joint has O-rings that seal the pipe.

·

Only disconnect the fuel tube joint by hand.

·

Do not forcibly bend, twist or turn the fuel pump tube.

·

Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

·

If the fuel tube joint and fuel suction plate are stuck, push and pull to release them.




Hide 77168A 9.REMOVE FUEL TANK VENT TUBE SET PLATE

a.
A218221

Remove the 8 bolts and set plate.


Hide 77020A 10.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A261658C03
0.659,1.29 0.826,1.446 0.167,0.156 10 *1 2.817,1.593 2.984,1.748 0.167,0.156 10 *2 1.445,0.932 1.005,1.372 1.005,1.372 0.855,1.372 false 2.484,1.843 2.652,1.676 2.652,1.676 2.757,1.676 false
*1 Fuel Suction Tube Set Gasket
*2 Suction Filter


Remove the fuel suction tube with pump and gauge assembly from the fuel tank.

NOTICE:
·

Do not damage the suction filter.

·

Make sure that the fuel sender gauge arm does not bend.




b.

Remove the fuel suction tube set gasket from the fuel suction tube assembly.