Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER POSITION SENSOR
RM2040EQ _52 Drivetrain _014701 P314 HYBRID TRANSMISSION / TRANSAXLE _0074953 SHIFT LEVER POSITION SENSOR A

P314 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 89451 1.INSTALL SHIFT LEVER POSITION SENSOR

a.

Install the shift lever position sensor to the manual valve shaft.


b.

Temporarily install the 2 bolts.


c.

Install a new lock plate and tighten the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


d.

Temporarily install the control shaft lever to the manual valve shaft.


e.
C245021
2.776,0.134 2.912,0.286 0.137,0.152 10 N

Turn the lever clockwise until it stops, then turn it counterclockwise 2 notches.


f.

Remove the control shaft lever from the manual valve shaft.


g.
C175439
1.975,2.353 2.171,2.497 0.196,0.144 10 *c 1.025,2.599 1.221,2.743 0.196,0.144 10 *b 0.717,2.611 0.913,2.755 0.196,0.144 10 *a 1.114,1.476 1.115,2.567 false 0.802,1.463 0.802,2.59 false
*a Neutral Basic Line
*b Protruding
*c Range of Play


Align the protruding part with the neutral basic line.

NOTICE:

There is play on the nut stopper side (protruding part). Align the center point of the range of the play with the neutral basic line.



h.
C245022N02
0.656,1.521 0.823,1.708 0.167,0.188 10 true 1 2.292,0.406 2.469,0.583 0.177,0.177 10 true 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


i.

Using a screwdriver, secure the nut with the lock plate.


j.

Install the control shaft lever, washer, and nut to the manual valve shaft.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


k.

Connect the connector to the shift lever position sensor.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.

Install a new clip to the control bracket.


c.
C245030
0.871,2.836 1.033,3.009 0.162,0.173 10 *1 2.891,0.424 3.053,0.597 0.162,0.173 10 *2 2.557,2.879 2.718,3.04 0.161,0.161 10 *b 0.877,0.391 1.037,0.552 0.161,0.161 10 *a 2.161,1.384 1.101,0.523 1.101,0.523 1.238,1.384 false 2.654,1.086 2.755,0.523 2.755,0.523 2.851,0.523 false 1.338,2.367 1.18,2.92 1.18,2.92 1.062,2.92 false 1.112,1.604 2.514,2.938 2.514,2.938 2.289,1.627 false
*1 Transmission Control Cable Assembly
*2 No. 1 Transmission Control Cable Bracket
*a Claw A
*b Claw B


Install the transmission control cable assembly to the control bracket.

NOTICE:
·

Make sure that the claws A on the clip are securely fit into the bracket holes.

·

Make sure that the cable is securely installed inside the claws B of the clip.




d.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 3.INSPECT SHIFT LEVER POSITION SENSOR POSITION

Hide 4.ADJUST SHIFT LEVER POSITION SENSOR POSITION

Hide 51442C 7.INSTALL ENGINE UNDER COVER LH

Hide 53852K 8.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441C 9.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 10.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH