Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID
RM2040EQ _54 Brake _014709 BRAKE SYSTEM (OTHER) _0074986 BRAKE FLUID N

BRAKE SYSTEM (OTHER)  BRAKE FLUID  BLEEDING  


CAUTION / NOTICE / HINT

CAUTION:

The intelligent tester must be used for air bleeding. If it is not used, the air bleeding will be incomplete, which is hazardous and may lead to an accident.


NOTICE:
·

Perform air bleeding with the shift lever in P and the parking brake applied.

·

As brake fluid may overflow when bleeding, do not place the fluid can on the reservoir filler opening.

·

Perform air bleeding while maintaining the brake fluid level between the MIN/MAX level on the brake fluid reservoir.

·

Air bleeding will be difficult if the following occurs:

1.

The brake actuator hose (the hose between the brake booster pump assembly and brake master cylinder reservoir assembly) is higher than the fluid level and air enters the hose.

2.

During the air bleeding procedure, air enters the brake booster pump assembly while the pump motor is operating.


·

While performing air bleeding, the accumulator pressure drop may cause a buzzer to sound. As there is no problem, continue with the operation.

·

During air bleeding, DTCs for pressure sensor malfunctions, etc. may be stored. After air bleeding and if instructed in the procedures, clear the DTCs.

·

Release the parking brake during the linear valve offset calibration procedure.

·

Do not allow brake fluid to adhere to any painted surface such as the vehicle body. If brake fluid leaks onto any painted surface, immediately clean it off.

·

When bleeding air, select the suitable work procedure according the table below.

Replaced/Installed Item Work Procedure
Flexible hose (front/rear) Bleed brake line
Disc brake cylinder assembly (front/rear)
Brake booster pump assembly Bleed brake system
Brake booster with master cylinder assembly
Brake master cylinder reservoir assembly



PROCEDURE

Hide 1.BLEED BRAKE LINE

a.

Bleed brake line.

i.
C242736

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT3



iii.

Connect the intelligent tester to the DLC3 and turn the power switch on (IG).


iv.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125

v.

Select "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.


vi.

After air bleeding, tighten each bleeder plug.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)



viii.

Turn the intelligent tester off and turn the power switch off.



b.

Inspect for brake fluid leaks.


c.

Install the brake master cylinder reservoir filler cap.


Hide 2.BLEED BRAKE SYSTEM

a.

Remove the front outer cowl top panel sub-assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


b.

Bleed the brake system.

i.
C242738

Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.

NOTICE:

Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.


HINT:

This procedure is not required if the reservoir level switch connector has been disconnected.



ii.
C242736

Remove the brake master cylinder reservoir filler cap assembly.


iii.

Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT3



iv.

Connect the intelligent tester to the DLC3 and turn the power switch on (IG).


v.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125

vi.

Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

NOTICE:

Before following the instructions on the intelligent tester to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.



vii.
C209151
1.646,1.323 2.094,1.771 2.094,1.771 2.344,1.771 false 2.375,1.677 2.625,1.906 0.25,0.229 10 false *1
*1 Stroke Simulator Bleeder Plug


After air bleeding, tighten each bleeder plug.

Torque:
disc brake cylinder bleeder plug : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
stroke simulator bleeder plug : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:

The stroke simulator bleeder plug is positioned as shown in the illustration.




ix.

Turn the intelligent tester off and turn the power switch off.



c.

Install the brake master cylinder reservoir filler cap.


d.

Inspect for brake fluid leaks.


e.

Install the outer cowl top panel sub-assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>INSTALLATION