Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER
RM2040EQ _54 Brake _014709 BRAKE SYSTEM (OTHER) _0074988 BRAKE BOOSTER A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C243027C02
1.177,0.552 1.177,0.302 1.177,0.302 1.969,0.302 false 1.635,0.656 1.635,0.313 false 1.99,0.208 2.271,0.51 0.281,0.302 10 false *a
*a Matchmark
V100135

Cut
V100145

Disposal Portion


Align the matchmarks on the wire harness and a new wire harness clamp, and install it to the wire harness.

NOTICE:

Make sure to install the wire harness clamp in the correct direction.



b.

Tighten the bands of the clamp and cut off the excess.


c.
C243050C03
1.917,2.698 2.333,2.698 false 1.802,3.25 0.74,2.885 0.74,2.885 1.365,3.365 false 3.01,3.323 3.135,3.323 false 2.563,3.5 2.781,3.719 2.781,3.719 2.938,3.719 false 1.667,3.875 2.302,4.313 2.302,4.313 1.542,4.104 false 2.365,2.615 2.604,2.833 0.24,0.219 10 false *1 3.167,3.24 3.385,3.438 0.219,0.198 10 false *3 2.969,3.635 3.188,3.854 0.219,0.219 10 false *4 2.333,4.24 2.573,4.448 0.24,0.208 10 false *5 0.563,2.792 0.802,3 0.24,0.208 10 false *2
*1 Connector Portion
*2 Union
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube


Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in bold in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




d.
C245590C02
1.448,0.906 1.302,0.615 1.302,0.615 1.115,0.615 false 1.438,1.052 1.01,0.729 1.01,0.729 0.938,0.729 false 1.396,1.292 1.125,1.677 1.125,1.677 0.927,1.677 false 1.49,1.365 1.49,1.896 1.49,1.896 1.573,1.896 false 1.938,1.094 1.938,1.74 1.938,1.74 2.01,1.74 false 0.958,0.531 1.177,0.719 0.219,0.188 10 false *a 0.781,0.656 0.99,0.854 0.208,0.198 10 false *b 0.771,1.583 1,1.813 0.229,0.229 10 false *c 1.594,1.813 1.781,2.01 0.188,0.198 10 false *d 2.031,1.646 2.24,1.833 0.208,0.188 10 false *e
*a to Front Wheel Cylinder LH (Way)
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.


e.

Using a union nut wrench, fully tighten each brake line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




f.
C243022C02
2.031,0.115 2.313,0.26 0.281,0.146 6 false '
V100135

Connect the connector
V100136

Lock the lock lever


Connect the connector to the brake booster with master cylinder assembly.

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.

·

Make sure that the connector lock is locked securely.




g.
C243026

Push in the wire harness clamp to install it to the brake booster with master cylinder assembly.


Hide 47264A 3.INSTALL PUSH ROD PIN

Hide 47234L 4.CONNECT NO. 1 RESERVOIR HOSE

a.
C243052C02
1.344,0.177 1.688,0.469 0.344,0.292 10 false 90° 1.906,0.177 2.375,0.5 0.469,0.323 10 false 180°
V100136

Up


Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly with the clip.

NOTICE:
·

When connecting the No. 1 reservoir hose, face the identification mark up.

·

Match the identification mark of the No. 1 reservoir hose and the rib of the brake booster with master cylinder assembly.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47235G 5.CONNECT NO. 2 RESERVOIR HOSE

a.
C243053C02
1.354,0.167 1.781,0.469 0.427,0.302 10 false 150° 1.948,0.156 2.417,0.469 0.469,0.313 10 false 120°
V100136

Up


Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly with the clip.

NOTICE:
·

When connecting the No. 2 reservoir hose, face the identification mark up.

·

Match the identification mark of the No. 2 reservoir hose and the identification mark of the brake booster with master cylinder assembly.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47238C 6.BLEED RESERVOIR TUBE

a.

Add brake fluid into the brake master cylinder reservoir assembly.


b.
C243024C02
1.333,0.583 0.875,0.958 0.875,0.958 0.76,0.958 false 0.604,0.875 0.865,1.146 0.26,0.271 10 false *1
*1 Reservoir Tube


Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the reservoir tube assembly.

NOTICE:
·

Do not damage the hoses or tubes.

·

Do not spill the brake fluid.

·

Continue this procedure until only a minor amount of air remains in the brake actuator tube.




Hide 47238C 7.INSTALL RESERVOIR TUBE

a.

Install the reservoir tube to the vehicle body with the 2 bolts and nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 47220D 8.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Engage the wire harness clamp.


Hide 9.FILL RESERVOIR WITH BRAKE FLUID

Hide 10.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

Hide 11.BLEED BRAKE SYSTEM

Hide 12.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 13.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 14.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 15.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 16.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 55702A 17.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install the front outer cowl top panel sub-assembly with the 10 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.


c.

Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.


Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.INSPECT AND ADJUST BRAKE PEDAL

Hide 20. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

HINT:

After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION