Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL
RM2040EQ _54 Brake _014709 BRAKE SYSTEM (OTHER) _0074987 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Turn back the dash panel insulator assembly from the slit provided on the dash panel insulator assembly.


iii.
C242734
2.292,1.604 2.635,1.604 false 1.688,3.865 1.5,4.052 1.5,4.052 1.229,4.052 false 2.677,1.51 2.938,1.76 0.26,0.25 10 false *1 1.073,3.958 1.365,4.219 0.292,0.26 10 false *2 2.625,3.844 2.906,4.104 0.281,0.26 10 false *a
*1 Stop Light Switch Assembly
*2 Asphalt Sheet
*a Brake Pedal Height


Measure the shortest distance between the brake pedal pad surface and asphalt sheet.

Pedal height from asphalt sheet:

143.2 to 153.2 mm (5.64 to 6.03 in.)


If pedal height is incorrect, inspect and adjust the push rod length according to the procedure below.



b.

Adjust the push rod length.

i.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Remove the brake booster with master cylinder assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


iii.
C242735
2.396,1.323 2.396,1.583 false 2.729,1.344 2.729,1.583 false 2.302,1.604 2.531,1.854 0.229,0.25 10 false *1 2.083,0.448 2.365,0.729 0.281,0.281 10 false *a 2.646,1.604 2.896,1.875 0.25,0.271 10 false *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis
*a Push Rod Length


Loosen the lock nut and adjust the push rod length shown in the illustration by turning the brake master cylinder push rod clevis to achieve the correct length.

Push rod length:

115.5 to 116.5 mm (4.55 to 4.58 in.)



iv.

Tighten the lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the brake booster with master cylinder assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>INSTALLATION

·

If the pedal height is incorrect even when the push rod length is adjusted, check the brake pedal support assembly and floor panel.

·

If necessary, replace the brake pedal support assembly.



vi.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



c.

After adjusting the pedal height, check the brake pedal free play.


Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.
C242733

Loosen the 2 bolts.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

e.
C242727

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.
C242733

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



g.

Turn the intelligent tester off and turn the power switch off.


h.

Disconnect the intelligent tester.


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708
2.167,1.583 2.427,1.844 0.26,0.26 10 false *a
*a Brake Pedal Free Play


Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:

Measure the distance at the same point used for the brake pedal height inspection.


a.

Release the parking brake.


b.

With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance.

Pedal reserve distance from the asphalt sheet at 500 N (51 kgf, 112 lbf):

More than 95 mm (3.74 in.)


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE


Hide 5. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE