Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2012.02–2015.04
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075005 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The power management control ECU has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the power management control ECU to the steering lock ECU is determined to be abnormal.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2782 Power Source Control ECU Malfunction Either condition is met (1-trip detection logic (Only output while a malfunction is present and the power switch is on (IG).)):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


·

Steering lock ECU (Steering lock actuator assembly)

·

Power management control ECU

·

Harness or connector


Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the power switch off. The steering unlocks when the power switch is turned on (ACC) or on (IG) while carrying the key.)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. Prohibits the hybrid control system from being started.

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2782
Entry&Start
·

Power Supply Short


-

WIRING DIAGRAM

C220331E08
0.177,3.157 1.51,3.517 1.332,0.36 10 Power Management Control ECU 0.177,2.998 0.491,3.173 0.314,0.175 10 I4 5.151,3.157 6.995,3.498 1.844,0.341 10 Steering Lock ECU (Steering Lock Actuator Assembly) 5.151,2.998 5.446,3.173 0.295,0.175 10 I24 0.817,0.803 1.233,0.978 0.416,0.175 10 SLR+ 1.27,0.696 1.473,0.87 0.203,0.175 10 6 5.174,0.696 5.377,0.87 0.203,0.175 10 3 5.38,0.803 5.684,0.978 0.304,0.175 10 IGE 5.38,1.97 5.735,2.145 0.355,0.175 10 GND 5.174,1.868 5.377,2.042 0.203,0.175 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly) or power management control ECU, registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I24 steering lock ECU connector.


c.
C157850C23
0.344,0.917 0.833,1.208 0.49,0.292 1.281,2.417 1.031,1.729 false 0.333,0.302 0.708,0.583 0.375,0.281 10 *a 0.51,0.99 1.156,1.417 0.646,0.427 10 I24 0.823,1.563 1.385,1.938 0.563,0.375 10 GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the I24 steering lock ECU connector.


e.

Turn the power switch off, make sure that the steering is unlocked and move the shift lever to P.


f.
C241547C16
0.25,0.667 0.594,0.948 0.344,0.281 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 false 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 false 2.115,4.198 2.115,4.458 false 1.854,1.104 1.083,1.917 false 0.219,0.208 0.542,0.438 0.323,0.229 10 *a 2.927,2.521 3.104,2.708 0.177,0.188 10 *b 2.042,4.469 2.344,4.667 0.302,0.198 10 *c 0.313,0.729 0.833,1.177 0.521,0.448 10 I24 0.938,1.948 1.458,2.208 0.521,0.26 10 IGE 2.708,1.958 3.25,2.417 0.542,0.458 10 GND 2.958,4.063 3.427,4.427 0.469,0.365 10 GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection I24-3 (IGE) - I24-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
a.

Clear the DTCs.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.CAUTION:

CAUTION:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING INTELLIGENT TESTER (POWER SUPPLY SHORT)
3.READ VALUE USING INTELLIGENT TESTER (POWER SUPPLY SHORT)
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B2782 is output.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

c.

Use the Data List to check if the steering lock control is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Short Record of malfunction of signal sent to steering lock motor (steering lock actuator assembly) from power management control ECU (short circuit) OK or NG(Past) OK: No record of malfunction (short circuit)
NG(Past): Record of malfunction (short circuit) exists
This item records malfunctions in the circuit between the power management control ECU and steering lock motor (steering lock actuator assembly).
Body Electrical > Entry&Start > Data List
Tester Display
Power Supply Short
50003 125 51

Result:
Result Proceed to
·

DTC B2782 is not output.

·

"OK" is displayed on the intelligent tester.


A
·

DTC B2782 is output.

·

"NG(Past)" is displayed on the intelligent tester.


B



A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the I24 steering lock ECU connector.


c.

Disconnect the I4 power management control ECU connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-3 (IGE) - I78-29 (SLR+) Always Below 1 Ω
I24-3 (IGE) - Body ground Always 10 kΩ or higher
I4-6 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR