The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an hybrid control system operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or power management control ECU is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the hybrid control system cannot be started.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to unlock steering wheel (Hybrid control system cannot start) |
|
- |
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.
To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, confirm that the problem does not occur.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch. This prevents the hybrid control system from starting while the steering is locked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in P, check that pressing the power switch with the brake pedal released causes the power source mode to change as follows:
Off → on (ACC) → on (IG) → off
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the Data List to check if the steering lock request is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of turning power switch on (IG) or on (ACC) or starting hybrid control system
NG: Except above |
·
If the unlock signal has not been received, the hybrid control system cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the power switch on (ACC) or on (IG) or starting the hybrid control system, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I24 steering lock ECU connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I24-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the connection which leads to ground.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I24-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I24 steering lock ECU connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | I24-3 (IGE) - I24-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.
To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG