Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075005 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Lock Steering Wheel  


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to lock steering wheel
Entry&Start
·

All items

Click here(Click here)


Main Body
·

FR Door Courtesy


-

WIRING DIAGRAM

C245393E04
5.385,3.292 5.698,3.479 0.313,0.188 10 false IGE 5.385,0.552 5.698,0.74 0.313,0.188 10 false LIN 5.385,4.083 5.792,4.271 0.406,0.188 10 false GND 5.177,0.396 5.344,0.583 0.167,0.188 10 false 5 5.177,3.188 5.344,3.375 0.167,0.188 10 false 3 5.177,3.958 5.344,4.146 0.167,0.188 10 false 1 5.167,4.906 5.427,5.094 0.26,0.188 10 false I24 5.167,5.073 6.948,5.635 1.781,0.563 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 2.49,1.24 2.771,1.427 0.281,0.188 10 false I87 2.49,1.385 4.021,1.99 1.531,0.604 10 false Certification ECU (Smart Key ECU Assembly) 2.979,5.042 4.677,5.333 1.698,0.292 10 false : LIN Communication Line 0.854,2.458 1.219,2.646 0.365,0.188 10 false LIN2 1.25,2.302 1.448,2.49 0.198,0.188 10 false 11 0.167,1.292 1.323,1.99 1.156,0.698 10 false Main Body ECU (Multiplex Network Body ECU) 0.813,3.292 1.24,3.479 0.427,0.188 10 false SLR+ 1.26,3.198 1.458,3.385 0.198,0.188 10 false 6 2.979,5.344 4.688,5.688 1.708,0.344 10 false : CAN Communication Line 3.375,0.552 3.656,0.74 0.281,0.188 10 false LIN 3.688,0.396 3.885,0.583 0.198,0.188 10 false 12 0.188,4.917 0.448,5.104 0.26,0.188 10 false I4 0.188,5.073 1.458,5.615 1.271,0.542 10 false Power Management Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

·

After performing repairs, confirm that the problem does not occur.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC (ALL)
a.

Using the intelligent tester, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGEMT TESTER (LOCK REQUEST RECEIVE)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.READ VALUE USING INTELLIGEMT TESTER (LOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of opening any door with power switch off and shift lever in P
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the intelligent tester screen.



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

5.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)
3.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
HINT:

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>B2782


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
HINT:

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>B2782


Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)
a.

Using the intelligent tester, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH CLOSE or OPEN CLOSE: Front door RH closed
OPEN: Front door RH open
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part.
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

NG

GO TO LIGHTING SYSTEM (FRONT DOOR COURTESY SWITCH CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the intelligent tester.


HINT:

Reasons for verification failure:

·

The steering lock ECU or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Turn the steering wheel and check the steering condition.

OK:

Steering is unlocked.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the intelligent tester.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE STEERING LOCK ACTUATOR ASSEMBLY