Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



WIRING DIAGRAM

C252894E12
2.365,1.156 2.219,0.813 2.219,0.813 2.083,0.813 false 4.396,1.156 4.583,0.781 4.583,0.781 4.833,0.781 false 0.781,2.688 1.208,2.885 0.427,0.198 10 false ECM 2.948,4.104 3.25,4.281 0.302,0.177 10 false A28 3.281,4.104 5.51,4.479 2.229,0.375 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 3,0.406 3.375,0.583 0.375,0.177 10 false DLC3 1.417,4.99 3.344,5.344 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.385,5 6.125,5.354 1.74,0.354 10 false : CAN Branch Line (CANH) 4.385,5.406 6.125,5.76 1.74,0.354 10 false : CAN Branch Line (CANL) 1.417,5.406 3.344,5.76 1.927,0.354 10 false : CAN Main Bus Line (CANL) 2.354,3.708 3.365,3.927 1.01,0.219 10 false ECU-IG1 NO. 1 1.354,3.948 2.208,4.156 0.854,0.208 10 false Trouble Area 3.51,3.573 3.844,3.76 0.333,0.188 10 false IG1 4.542,3.604 4.958,3.781 0.417,0.177 10 false GND 3.771,3.281 4.198,3.458 0.427,0.177 10 false CA1H 4.271,3.292 4.667,3.469 0.396,0.177 10 false CA1L 3.25,3.469 3.51,3.646 0.26,0.177 10 false 16 4.938,3.479 5.146,3.656 0.208,0.177 10 false 28 3.76,3.083 4.031,3.26 0.271,0.177 10 false 37 4.448,3.083 4.656,3.26 0.208,0.177 10 false 38 0.25,0.729 2.24,0.917 1.99,0.188 10 false CAN Junction LH1 Connector 4.896,0.688 6.906,0.875 2.01,0.188 10 false CAN Junction RH1 Connector 5.813,2.688 7.021,3.031 1.208,0.344 10 false Combination Meter Assembly 0.719,2.115 1.167,2.26 0.448,0.146 10 false 120 Ω 6.156,2.115 6.604,2.26 0.448,0.146 10 false 120 Ω 0.104,0 1.646,0.323 1.542,0.323 12 false V Bus: 0.438,2.688 0.781,2.885 0.344,0.198 10 false A25 5.542,2.688 5.813,2.885 0.271,0.198 10 false I18

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:

DTC C1241 is not output.


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

NG

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.
C209401C80
1.552,0.771 1.969,1.042 0.417,0.271 1.958,2.135 1.583,2.677 false 2.063,2.135 2.448,2.677 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.615,0.823 1.906,0.979 0.292,0.156 10 false A28 1.292,2.698 1.677,2.875 0.385,0.177 10 false CA1H 2.333,2.698 2.698,2.875 0.365,0.177 10 false CA1L
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-37 (CA1H) - A28-38 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)