Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Main body ECU (multiplex network body ECU) branch line or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) ground circuit or instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly



WIRING DIAGRAM

C252900E02
4.99,1.135 4.833,1.135 4.833,1.135 4.479,1.792 false 2.969,1.49 3.156,1.49 3.156,1.49 3.448,1.792 false 3.573,1.073 4.083,1.385 0.51,0.313 10 false DLC3 1.281,2.354 2.469,2.771 1.188,0.417 10 false Combination Meter Assembly 2.323,8.01 4.323,8.313 2,0.302 10 false : CAN Main Bus Line (CANH) 5.156,8.01 6.906,8.292 1.75,0.281 10 false : CAN Branch Line (CANH) 5.156,8.417 6.885,8.688 1.729,0.271 10 false : CAN Branch Line (CANL) 2.313,8.406 4.292,8.688 1.979,0.281 10 false : CAN Main Bus Line (CANL) 2.854,4.448 3.667,4.75 0.813,0.302 10 false IG1 NO. 2 5.083,1.031 7.063,1.323 1.979,0.292 10 false CAN Junction LH1 Connector 1.094,1.385 3.115,1.698 2.021,0.313 10 false CAN Junction RH1 Connector 6.625,5.406 7.104,5.875 0.479,0.469 10 false Trouble Area 4.625,4.99 5.156,5.292 0.531,0.302 10 false BECU 4.875,3.354 5.344,3.656 0.469,0.302 10 false CANH 5.344,3.354 5.844,3.656 0.5,0.302 10 false CANL 2.354,4.823 2.615,5.042 0.26,0.219 10 false 31 4.865,2.948 5.104,3.177 0.24,0.229 10 false 14 5.531,2.948 5.76,3.198 0.229,0.25 10 false 13 5.01,3.135 5.333,3.344 0.323,0.208 10 false I13 2.344,5.01 2.677,5.25 0.333,0.24 10 false 3D 5.406,3.135 5.802,3.427 0.396,0.292 10 false I13 6.25,2.719 6.729,3 0.479,0.281 10 false 120 Ω 2.76,2.708 3.219,2.948 0.458,0.24 10 false 120 Ω 6.375,2.99 6.823,3.26 0.448,0.271 10 false ECM 0.156,0.135 0.792,0.531 0.635,0.396 12 false V Bus: 2,7.094 3.594,7.667 1.594,0.573 10 false Instrument Panel Junction Block Assembly 2.344,4.615 2.635,4.896 0.292,0.281 10 false 3B 2.406,4.417 2.635,4.688 0.229,0.271 10 false 7 2.344,4.177 2.635,4.427 0.292,0.25 10 false 3A 2.365,3.969 2.635,4.198 0.271,0.229 10 false 27 2.354,3.698 2.635,3.958 0.281,0.26 10 false 3F 2.385,3.5 2.646,3.76 0.26,0.26 10 false 1 1.635,3.865 2.25,4.167 0.615,0.302 10 false DC/DC 1.646,5.604 2.125,5.958 0.479,0.354 10 false DC/DC 3.448,3.927 4.5,4.229 1.052,0.302 10 false ECU-IG1 NO. 2 4.281,3.51 4.552,3.729 0.271,0.219 10 false 32 4.25,3.698 4.563,3.948 0.313,0.25 10 false MB 4.271,4.813 4.51,5.031 0.24,0.219 10 false 30 4.281,6.583 4.583,6.854 0.302,0.271 10 false 11 4.26,6.781 4.615,7.021 0.354,0.24 10 false MB 4.24,5.01 4.615,5.292 0.375,0.281 10 false MB 4.635,3.677 4.896,3.958 0.26,0.281 10 false IG 2.354,5.438 2.656,5.708 0.302,0.271 10 false 3F 2.385,5.24 2.583,5.49 0.198,0.25 10 false 1 2.344,5.906 2.656,6.167 0.313,0.26 10 false 3B 2.354,5.708 2.635,5.938 0.281,0.229 10 false 23 2.813,6.177 3.583,6.469 0.771,0.292 10 false ACC NO. 1 2.344,6.344 2.635,6.604 0.292,0.26 10 false 3B 2.396,6.156 2.635,6.396 0.24,0.24 10 false 7 4.625,5.406 5.135,5.76 0.51,0.354 10 false ACC 4.24,5.438 4.563,5.719 0.323,0.281 10 false MB 4.271,5.25 4.531,5.5 0.26,0.25 10 false 29 3.458,5.594 4.323,5.938 0.865,0.344 10 false ECU-ACC 2.406,6.583 2.583,6.771 0.177,0.188 10 false 7 2.344,6.771 2.635,7.01 0.292,0.24 10 false 3B 4.625,6.771 5.219,7.031 0.594,0.26 10 false GND1 4.563,7.156 6.198,7.625 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 0.646,4.146 1.469,4.771 0.823,0.625 10 false from Power Management Control ECU 0.656,5.896 1.49,6.615 0.833,0.719 10 false from Power Management Control ECU 1.333,5.177 2.25,5.479 0.917,0.302 10 false ECU-B NO. 1 0.979,2.354 1.344,2.563 0.365,0.208 10 false I18 6.063,2.99 6.438,3.281 0.375,0.292 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C240484C04
0.281,2 0.656,2.25 0.375,0.25 1.625,0.49 1.875,0.49 1.875,0.49 1.875,2.198 false 2.219,0.5 2,0.5 2,0.5 2,2.198 false 0.135,0.135 0.427,0.479 0.292,0.344 10 false *a 2.292,0.406 2.844,0.677 0.552,0.271 10 false CANH 1.198,0.396 1.677,0.677 0.479,0.281 10 false CANL 0.375,2.031 0.656,2.208 0.281,0.177 10 false I13
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-14 (CANH) - I13-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the instrument panel junction block assembly 2 connectors.


b.
C223282C04
1.656,0.531 1.99,0.781 0.333,0.25 1.656,2.875 2,3.125 0.344,0.25 2.229,1.26 2.229,0.573 2.229,0.573 2.417,0.573 false 1.302,3.885 1.302,4.281 false 1.729,0.563 1.917,0.729 0.188,0.167 10 false 3B 1.115,4.313 1.625,4.573 0.51,0.26 10 false BECU 2.479,0.479 2.979,0.74 0.5,0.26 10 false GND1 0.156,0.115 0.51,0.479 0.354,0.365 10 false *a 1.74,2.906 1.948,3.073 0.208,0.167 10 false 3D
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3D-31 (BECU) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY AND ACC NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY AND ACC NO. 1 RELAY)
a.

Remove the instrument panel junction block assembly

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E191506C17
1.927,0.281 2.24,0.49 0.313,0.208 5.281,0.365 5.594,0.573 0.313,0.208 1.146,2.188 1.458,2.396 0.313,0.208 4.563,2.354 4.875,2.563 0.313,0.208 6.51,3.052 6.594,3.448 6.594,3.448 6.677,3.448 false 6.167,3.042 6.063,3.448 6.063,3.448 5.969,3.448 false 2,0.313 2.26,0.521 0.26,0.208 10 false 3A 5.365,0.396 5.625,0.604 0.26,0.208 10 false 3B 1.229,2.219 1.49,2.427 0.26,0.208 10 false 3F 4.615,2.385 4.875,2.594 0.26,0.208 10 false MB 6.729,3.365 6.938,3.563 0.208,0.198 10 false IG 0.156,0.156 0.448,0.469 0.292,0.313 10 false *a 5.656,3.385 6.01,3.573 0.354,0.188 10 false ACC
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
3F-1 - MB-32 (IG) Always 10 kΩ or higher
3F-1 - MB-32 (IG) Auxiliary battery positive (+) → 3A-27
Auxiliary battery negative (-) → 3B-7
Below 1 Ω
3F-1 - MB-29 (ACC) Always 10 kΩ or higher
3F-1 - MB-29 (ACC) Auxiliary battery positive (+) → 3B-23
Auxiliary battery negative (-) → 3B-7
Below 1 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY