| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U0200 | Lost Communication with "Door Control Module B" | No communication from the outer mirror control ECU assembly continues. | ·
Outer mirror control ECU assembly (for front passenger side) branch line or connector ·
Power source circuit of outer mirror control ECU assembly (for front passenger side) ·
Outer mirror control ECU assembly (for front passenger side) ground circuit ·
Outer mirror control ECU assembly (for front passenger side) |
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. |
This diagnosis procedure is for when DTC U0200 is output by the main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body).
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), wait at least 20 seconds.
After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Reconfirm DTCs.
If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the sub bus 1.
| Result | Proceed to |
|---|---|
| U1002 is not output from main body ECU (multiplex network body ECU).
(Intelligent tester display: Main Body) |
A |
| U1002 is output from main body ECU (multiplex network body ECU).
(Intelligent tester display: Main Body) |
B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the outer mirror control ECU assembly (for front passenger side) connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-9 (CANP) - K12-8 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-7 (GND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-6 (CPUB) - Body ground | Power switch off | 11 to 14 V |
| K12-5 (SIG) - Body ground | Power switch on (IG) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG