Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Main Body ECU)  


DESCRIPTION

·

The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 1.

·

When the main body ECU receives a response signal from the ECUs connected to sub bus 1, the main body ECU recognizes and memorizes that the ECU is connected to sub bus 1. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to sub bus 1 when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 1, the main body ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Main Body ECU) Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
·

Open or short in sub bus 1 main line or connector

·

Open or short in sub bus 1 branch line or connector

·

Main body ECU (Multiplex network body ECU)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Position control ECU and switch assembly (for Driver side)

·

Open or short in CAN junction LH2 connector

·

Open or short in CAN junction RH2 connector


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnosis procedure is for when DTC U1002 is output by the main body ECU (Intelligent tester display: Main Body).


WIRING DIAGRAM

C259928E04
0.375,0.656 1.583,0.844 1.208,0.188 10 false x: Suspected Area 4.667,0.677 6.354,1.083 1.688,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.208,0.49 3.625,0.677 0.417,0.188 10 false 120 Ω 2.51,1.167 2.948,1.333 0.438,0.167 10 false CANN 2.594,1.406 2.802,1.573 0.208,0.167 10 false 10 2.677,1.656 2.938,1.823 0.26,0.167 10 false GR 3.865,1.656 4.073,1.823 0.208,0.167 10 false R 4.031,1.406 4.24,1.573 0.208,0.167 10 false 9 4.396,0.677 4.76,0.844 0.365,0.167 10 false I12 3.865,1.167 4.292,1.333 0.427,0.167 10 false CANP 0.094,0.063 1.052,0.344 0.958,0.281 12 false Sub Bus 1: 1.396,2.469 2.594,2.865 1.198,0.396 10 false CAN Junction LH2 Connector 2.667,2.031 2.875,2.198 0.208,0.167 10 false 2 3.969,2.021 4.177,2.188 0.208,0.167 10 false 1 5.052,2.188 5.26,2.354 0.208,0.167 10 false G 5.01,2.969 5.281,3.135 0.271,0.167 10 false GR 2.865,2.031 3.167,2.198 0.302,0.167 10 false I162 3.615,2.031 3.906,2.198 0.292,0.167 10 false I162 4.229,2.948 4.438,3.115 0.208,0.167 10 false 2 4.229,2.208 4.438,2.375 0.208,0.167 10 false 1 4.146,2.396 4.448,2.563 0.302,0.167 10 false I163 4.146,2.771 4.448,2.938 0.302,0.167 10 false I163 2.865,3.219 3.156,3.385 0.292,0.167 10 false I166 3.625,3.219 3.917,3.385 0.292,0.167 10 false I166 4,3.219 4.208,3.385 0.208,0.167 10 false 1 2.677,3.219 2.885,3.385 0.208,0.167 10 false 2 5.708,2.302 5.917,2.469 0.208,0.167 10 false 9 5.708,2.865 5.99,3.031 0.281,0.167 10 false 8 5.896,2.229 6.333,2.396 0.438,0.167 10 false CANP 5.896,2.927 6.333,3.094 0.438,0.167 10 false CANN 2.688,3.563 2.958,3.729 0.271,0.167 10 false GR 3.896,3.563 4.104,3.729 0.208,0.167 10 false Y 4,3.948 4.208,4.115 0.208,0.167 10 false 1 2.688,3.948 2.865,4.115 0.177,0.167 10 false 2 2.865,3.958 3.156,4.125 0.292,0.167 10 false I167 3.615,3.958 3.906,4.125 0.292,0.167 10 false I167 4.156,6.969 5.406,7.365 1.25,0.396 10 false CAN Junction RH2 Connector 3.198,7.208 3.615,7.396 0.417,0.188 10 false 120 Ω 3.906,8 5.615,8.188 1.708,0.188 10 false : CAN Branch Line (CANH) 3.906,8.417 5.615,8.604 1.708,0.188 10 false : CAN Branch Line (CANL) 0.938,8 2.854,8.188 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.938,8.417 2.854,8.604 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.427,5.25 2.635,5.417 0.208,0.167 10 false 2 2.427,4.5 2.635,4.667 0.208,0.167 10 false 1 2.344,4.688 2.646,4.854 0.302,0.167 10 false I164 2.344,5.052 2.646,5.219 0.302,0.167 10 false I164 1.823,4.5 2.031,4.667 0.208,0.167 10 false P 1.76,5.271 2.031,5.438 0.271,0.167 10 false GR 1.438,4.583 1.646,4.75 0.208,0.167 10 false 9 1.438,5.177 1.719,5.344 0.281,0.167 10 false 8 0.938,4.552 1.375,4.719 0.438,0.167 10 false CANP 0.927,5.229 1.365,5.396 0.438,0.167 10 false CANN 4.229,6.167 4.438,6.333 0.208,0.167 10 false 2 4.24,5.406 4.448,5.573 0.208,0.167 10 false 1 4.146,5.594 4.448,5.76 0.302,0.167 10 false I165 4.146,5.958 4.448,6.125 0.302,0.167 10 false I165 5.729,3.135 7.146,3.708 1.417,0.573 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 5.427,3.135 5.781,3.302 0.354,0.167 10 false K12 0.313,5.458 1.615,6.01 1.302,0.552 10 false Outer Mirror Control ECU Assembly (for Driver Side) 0.052,5.458 0.302,5.625 0.25,0.167 10 false J13 5.792,6.5 7.135,7.021 1.344,0.521 10 false Position Control ECU and Switch Assembly (for Driver Side) 5.792,6.344 6.083,6.51 0.292,0.167 10 false d12 4.688,6.146 4.958,6.313 0.271,0.167 10 false GR 5.698,5.479 5.906,5.646 0.208,0.167 10 false 8 5.698,6.083 5.979,6.25 0.281,0.167 10 false 7 5.865,5.427 6.302,5.594 0.438,0.167 10 false CANP 5.865,6.115 6.302,6.281 0.438,0.167 10 false CANN 4.688,5.396 4.958,5.563 0.271,0.167 10 false BE 5.375,6.146 5.594,6.313 0.219,0.167 10 false W 5.396,5.396 5.531,5.563 0.135,0.167 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C236433C11
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.385,1.594 1.927,1.01 1.927,1.01 2.104,1.01 true 2.698,2.25 2.552,2.25 2.552,2.25 1.406,1.802 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.719,2.188 3.333,2.385 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I162-1 (CANH) -I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

2.RECONFIRM DTC OUTPUT

B

3.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

7.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

13.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
2.RECONFIRM DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Clear the DTCs.


f.

Turn the power switch off.


g.

Turn the power switch on (IG) and recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
U1002 is output from main body ECU (multiplex network body ECU).
(Intelligent tester display: Main Body)
A
Other DTC is output. B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I162) from the CAN junction LH2 connector.


b.
C235315C06
1.104,0.521 1.656,0.865 0.552,0.344 2.698,2.052 2.521,2.052 2.521,2.052 1.781,1.646 true 1.75,1.406 2.281,0.76 2.281,0.76 2.49,0.76 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.25,0.594 1.865,0.792 0.615,0.198 10 false I162 2.563,0.667 3.219,0.927 0.656,0.26 10 false CANH*b 2.74,1.969 3.313,2.188 0.573,0.219 10 false CANL*b
*a Rear view of wire harness connector
(to CAN Junction LH2 Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



Result:
Result
OK
NG



OK

4.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2)

NG

6.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
4.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2)
a.

Reconnect the wire harness connector (I162) to the CAN junction LH2 connector.


b.

Disconnect the wire harness connector (I166) from the CAN junction LH2 connector.


c.
C247989C05
0.823,0.552 1.26,0.813 0.438,0.26 1.979,0.771 1.75,0.771 1.75,0.771 1.469,1.344 true 2.74,2.021 2.563,2.021 2.563,2.021 1.5,1.552 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.906,0.604 1.521,0.802 0.615,0.198 10 false I166 2.052,0.677 2.969,0.875 0.917,0.198 10 false CANH*b 2.802,1.948 3.354,2.177 0.552,0.229 10 false CANL*b
*a Rear view of wire harness connector
(to CAN Junction LH2 Connector)
*b to CAN Junction RH2 Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I166-1 (CANH) - I166-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION LH2 CONNECTOR

NG

5.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2 - CAN J/C RH2)
5.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN J/C LH2 - CAN J/C RH2)
a.

Reconnect the wire harness connector (I166) to the CAN junction LH2 connector.


b.

Disconnect the wire harness connector (I167) from the CAN junction RH2 connector.


c.
C247989C06
0.823,0.552 1.26,0.813 0.438,0.26 1.979,0.76 1.75,0.76 1.75,0.76 1.469,1.333 true 2.729,2.021 2.552,2.021 2.552,2.021 1.49,1.552 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.906,0.604 1.521,0.802 0.615,0.198 10 false I167 2.052,0.677 2.969,0.875 0.917,0.198 10 false CANH*b 2.781,1.948 3.333,2.177 0.552,0.229 10 false CANL*b
*a Rear view of wire harness connector
(to CAN Junction RH2 Connector)
*b to CAN Junction LH2 Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I167-1 (CANH) - I167-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION RH2 CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - CAN J/C RH2)

6.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I162) to the CAN junction LH2 connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C01
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

7.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I162) from the CAN junction LH2 connector.


b.
C235315C06
1.104,0.521 1.656,0.865 0.552,0.344 2.698,2.052 2.521,2.052 2.521,2.052 1.781,1.646 true 1.75,1.406 2.281,0.76 2.281,0.76 2.49,0.76 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.25,0.594 1.865,0.792 0.615,0.198 10 false I162 2.563,0.667 3.219,0.927 0.656,0.26 10 false CANH*b 2.74,1.969 3.313,2.188 0.573,0.219 10 false CANL*b
*a Rear view of wire harness connector
(to CAN Junction LH2 Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

8.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)

NG

12.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
8.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)
a.

Reconnect the wire harness connector (I162) to the CAN junction LH2 connector.


b.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN Junction LH2 Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the main body ECU main line harness connector.


c.

While observing the resistance value shown on the tester, disconnect connectors (I163, I168, I186 and I164) from the CAN junction LH2 connector or CAN junction RH2 connector one by one until the resistance becomes normal (between 54 and 69 Ω).

C259929C01
1.74,1.573 2.052,1.729 0.313,0.156 10 false *1 4.802,1.583 5.115,1.74 0.313,0.156 10 false *2 3.49,0.406 3.802,0.563 0.313,0.156 10 false *3 1.729,2.802 2.042,2.958 0.313,0.156 10 false *4 3.76,2.802 4.073,2.958 0.313,0.156 10 false *5 3.49,4.042 3.802,4.198 0.313,0.156 10 false *6 1.49,1.063 1.802,1.219 0.313,0.156 10 false R 2.052,1.073 2.365,1.229 0.313,0.156 10 false GR 5.094,1.073 5.406,1.229 0.313,0.156 10 false GR 4.573,1.073 4.885,1.229 0.313,0.156 10 false G 6.844,1.427 7.156,1.583 0.313,0.156 10 false GR 6.313,1.427 6.625,1.583 0.313,0.156 10 false Y 0.063,3.052 0.375,3.208 0.313,0.156 10 false Y 0.542,3.052 0.854,3.208 0.313,0.156 10 false GR 1.99,3.417 2.302,3.573 0.313,0.156 10 false GR 1.521,3.427 1.833,3.583 0.313,0.156 10 false P 4.052,3.563 4.365,3.719 0.313,0.156 10 false GR 3.479,3.563 3.792,3.719 0.313,0.156 10 false BE 3.563,3.177 3.875,3.333 0.313,0.156 10 false L 4.083,3.188 4.396,3.344 0.313,0.156 10 false W
*1 Main Body ECU (Multiplex Network Body ECU) *2 Outer Mirror Control ECU Assembly (for Front Passenger Side)
*3 CAN Junction LH2 Connector *4 Outer Mirror Control ECU Assembly (for Driver Side)
*5 Position Control ECU and Switch Assembly (for Driver Side) *6 CAN Junction RH2 Connector


C247999C08
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN Junction LH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction LH2 Connector)


Wiring Color:
CAN Junction LH2 Connector Side Code Color (CANH Side) Color (CANL Side)
Main body ECU (Multiplex network body ECU) I162 R GR
Outer mirror control ECU assembly (for Front passenger side) I163 G GR
CAN main bus line (bus line connecting CAN junction LH2 connector and CAN junction RH2 connector) I166 Y GR


C259930C06
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.542 false 1.573,5.031 1.135,4.875 false 0.094,0.073 0.531,0.396 0.438,0.323 10 false *1 1.354,0.646 1.792,0.969 0.438,0.323 10 false *a 4.438,0.656 4.875,0.979 0.438,0.323 10 false *b 6.406,2.563 6.844,2.885 0.438,0.323 10 false *c 0.563,4.052 1,4.375 0.438,0.323 10 false *d 1.594,4.458 2.125,4.688 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.469 5.073,4.677 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.177 5.073,5.385 0.458,0.208 10 false I167
*1 CAN Junction RH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction RH2 Connector)


Wiring Color:
CAN Junction RH2 Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN junction LH2 connector and CAN junction RH2 connector) I167 Y GR
Position control ECU and switch assembly (for Driver side) I165 BE GR
Outer mirror control ECU assembly (for Driver side) I164 P GR


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Symptom Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

9.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2)

B

11.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
9.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2)
a.

Disconnect the wire harness connector (I166) from the CAN junction LH2 connector.


b.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

10.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2 - CAN J/C RH2)

NG

REPLACE CAN JUNCTION LH2 CONNECTOR

10.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN J/C LH2 - CAN J/C RH2)
a.

Reconnect the wire harness connector (I166) to the CAN junction LH2 connector.


b.

Disconnect the wire harness connector (I167) from the CAN junction RH2 connector.


c.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION RH2 CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - CAN J/C RH2)

11.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
a.

Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU, there may be a short in the ECU.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

12.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I162) to the CAN junction LH2 connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C01
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

13.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I162) from the CAN junction LH2 connector.


b.
C236584C05
1.5,0.583 1.917,0.896 0.417,0.313 0.135,3.719 0.531,3.99 0.396,0.271 1.635,3.542 1.958,3.083 1.958,3.083 2.104,3.083 false 2.344,4.104 2.594,4.385 2.594,4.385 2.781,4.385 false 1.063,0.76 1.24,0.76 1.24,0.76 1.667,1.354 true 1.26,2.563 1.427,2.563 1.427,2.563 1.698,1.563 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.573,0.656 1.938,0.896 0.365,0.24 10 false I162 0.208,2.979 0.521,3.177 0.313,0.198 10 false *1 0.24,3.76 0.698,3.958 0.458,0.198 10 false I39 2.177,3.021 2.49,3.219 0.313,0.198 10 false CG 2.833,4.313 3.292,4.51 0.458,0.198 10 false BAT 0.531,0.667 1.156,0.906 0.625,0.24 10 false CANH*b 0.719,2.49 1.635,2.688 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to CAN Junction LH2 Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

14.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)

NG

18.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
14.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)
a.

Reconnect the wire harness connector (I162) to the CAN junction LH2 connector.


b.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN Junction LH2 Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the wire harness connector (I162) and CG or BAT of the DLC3.

HINT:

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.



c.

While observing the resistance value shown on the ohmmeter, disconnect branch line connectors (I184, I185, I186 and I190) from the CAN junction LH2 connector or CAN junction RH2 connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C259929C01
1.74,1.573 2.052,1.729 0.313,0.156 10 false *1 4.802,1.583 5.115,1.74 0.313,0.156 10 false *2 3.49,0.406 3.802,0.563 0.313,0.156 10 false *3 1.729,2.802 2.042,2.958 0.313,0.156 10 false *4 3.76,2.802 4.073,2.958 0.313,0.156 10 false *5 3.49,4.042 3.802,4.198 0.313,0.156 10 false *6 1.49,1.063 1.802,1.219 0.313,0.156 10 false R 2.052,1.073 2.365,1.229 0.313,0.156 10 false GR 5.094,1.073 5.406,1.229 0.313,0.156 10 false GR 4.573,1.073 4.885,1.229 0.313,0.156 10 false G 6.844,1.427 7.156,1.583 0.313,0.156 10 false GR 6.313,1.427 6.625,1.583 0.313,0.156 10 false Y 0.063,3.052 0.375,3.208 0.313,0.156 10 false Y 0.542,3.052 0.854,3.208 0.313,0.156 10 false GR 1.99,3.417 2.302,3.573 0.313,0.156 10 false GR 1.521,3.427 1.833,3.583 0.313,0.156 10 false P 4.052,3.563 4.365,3.719 0.313,0.156 10 false GR 3.479,3.563 3.792,3.719 0.313,0.156 10 false BE 3.563,3.177 3.875,3.333 0.313,0.156 10 false L 4.083,3.188 4.396,3.344 0.313,0.156 10 false W
*1 Main Body ECU (Multiplex Network Body ECU) *2 Outer Mirror Control ECU Assembly (for Front Passenger Side)
*3 CAN Junction LH2 Connector *4 Outer Mirror Control ECU Assembly (for Driver Side)
*5 Position Control ECU and Switch Assembly (for Driver Side) *6 CAN Junction RH2 Connector


C247999C08
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN Junction LH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction LH2 Connector)


Wiring Color:
CAN Junction LH2 Connector Side Code Color (CANH Side) Color (CANL Side)
Main body ECU (Multiplex network body ECU) I162 R GR
Outer mirror control ECU assembly (for Front passenger side) I163 G GR
CAN main bus line (bus line connecting CAN junction LH2 connector and CAN junction RH2 connector) I166 Y GR


C259930C06
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.542 false 1.573,5.031 1.135,4.875 false 0.094,0.073 0.531,0.396 0.438,0.323 10 false *1 1.354,0.646 1.792,0.969 0.438,0.323 10 false *a 4.438,0.656 4.875,0.979 0.438,0.323 10 false *b 6.406,2.563 6.844,2.885 0.438,0.323 10 false *c 0.563,4.052 1,4.375 0.438,0.323 10 false *d 1.594,4.458 2.125,4.688 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.469 5.073,4.677 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.177 5.073,5.385 0.458,0.208 10 false I167
*1 CAN Junction RH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction RH2 Connector)


Wiring Color:
CAN Junction RH2 Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN junction LH2 connector and CAN junction RH2 connector) I167 Y GR
Position control ECU and switch assembly (for Driver side) I165 BE GR
Outer mirror control ECU assembly (for Driver side) I164 P GR



Result:
Result Proceed to
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to +B in the branch lines.)
A
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to GND in the branch lines.)
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas related to one or more of the disconnected branch lines.)
B
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas related to one or more of the disconnected branch lines.)



A

15.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2)

B

17.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
15.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2)
a.

Disconnect the wire harness connector (I166) from the CAN junction LH2 connector.


b.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

16.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2 - CAN J/C RH2)

NG

REPLACE CAN JUNCTION LH2 CONNECTOR

16.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN J/C LH2 - CAN J/C RH2)
a.

Reconnect the wire harness connector (I166) to the CAN junction LH2 connector.


b.

Disconnect the wire harness connector (I167) from the CAN junction RH2 connector.


c.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION RH2 CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - CAN J/C RH2)

17.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
a.

Reconnect the connector for the bus line that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN Junction LH2 Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

18.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.
C236584C05
1.5,0.583 1.917,0.896 0.417,0.313 0.135,3.719 0.531,3.99 0.396,0.271 1.635,3.542 1.958,3.083 1.958,3.083 2.104,3.083 false 2.344,4.104 2.594,4.385 2.594,4.385 2.781,4.385 false 1.063,0.76 1.24,0.76 1.24,0.76 1.667,1.354 true 1.26,2.563 1.427,2.563 1.427,2.563 1.698,1.563 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.573,0.656 1.938,0.896 0.365,0.24 10 false I162 0.208,2.979 0.521,3.177 0.313,0.198 10 false *1 0.24,3.76 0.698,3.958 0.458,0.198 10 false I39 2.177,3.021 2.49,3.219 0.313,0.198 10 false CG 2.833,4.313 3.292,4.51 0.458,0.198 10 false BAT 0.531,0.667 1.156,0.906 0.625,0.24 10 false CANH*b 0.719,2.49 1.635,2.688 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to CAN Junction LH2 Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH2 - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))