Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0208 Lost Communication with "Seat Control Module A" No communication from the position control ECU and switch assembly continues.
·

Position control ECU and switch assembly (for driver side) branch line or connector

·

Power source circuit of position control ECU and switch assembly (for driver side)

·

Position control ECU and switch assembly (for driver side) ground circuit

·

Position control ECU and switch assembly (for driver side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnosis procedure is for when DTC U0208 is output by the main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body).


WIRING DIAGRAM

C252887E04
1.781,0.719 2,0.156 2,0.156 2.115,0.156 false 0.146,0.083 1.979,0.323 1.833,0.24 12 false Sub Bus 1: 2.177,0.063 4.177,0.333 2,0.271 10 false CAN Junction LH2 Connector 5.156,2.25 7.104,2.469 1.948,0.219 10 false CAN Junction RH2 Connector 0.708,1.656 1.479,1.854 0.771,0.198 10 false 120 Ω 6.083,1.667 6.854,1.865 0.771,0.198 10 false 120 Ω 0.094,2.281 0.323,2.469 0.229,0.188 10 false I12 0.323,2.281 1.479,2.906 1.156,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 4.021,2.521 4.281,2.719 0.26,0.198 10 false d12 4.427,2.521 4.708,2.719 0.281,0.198 10 false d12 4.76,2.521 4.917,2.719 0.156,0.198 10 false 7 3.833,2.531 3.99,2.729 0.156,0.198 10 false 8 3.406,2.708 3.563,2.906 0.156,0.198 10 false 7 3.333,2.906 3.635,3.104 0.302,0.198 10 false d11 5.115,3.052 5.375,3.292 0.26,0.24 10 false d11 5.177,2.844 5.333,3.042 0.156,0.198 10 false 2 3.896,2.719 4.313,2.927 0.417,0.208 10 false CANP 4.396,2.719 5.01,2.917 0.615,0.198 10 false CANN 3.667,2.906 3.979,3.104 0.313,0.198 10 false +B 3.333,3.323 3.792,3.521 0.458,0.198 10 false d12 3.365,3.135 3.677,3.333 0.313,0.198 10 false 12 3.677,3.313 4.292,3.51 0.615,0.198 10 false SYSB 4.677,3.042 5.135,3.24 0.458,0.198 10 false GND 3.594,3.667 5.615,4.063 2.021,0.396 10 false Position Control ECU and Switch Assembly (for Driver Side) 3.656,4.542 5.49,4.74 1.833,0.198 10 false Trouble Area 1.396,4.948 3.24,5.156 1.844,0.208 10 false : CAN Main Bus Line (CANH) 1.406,5.344 3.271,5.563 1.865,0.219 10 false : CAN Main Bus Line (CANL) 4.406,4.948 6.135,5.208 1.729,0.26 10 false : CAN Branch Line (CANH) 4.417,5.344 6.156,5.552 1.74,0.208 10 false : CAN Branch Line (CANL) 2.396,3.073 3.208,3.323 0.813,0.25 10 false P/SEAT FR 2.417,3.479 3.396,3.667 0.979,0.188 10 false ECU-B NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 20 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the sub bus 1.



Result:
Result Proceed to
U1002 is not output from main body ECU (multiplex network body ECU).
(Intelligent tester display: Main Body)
A
U1002 is output from main body ECU (multiplex network body ECU).
(Intelligent tester display: Main Body)
B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the position control ECU and switch assembly connector.


c.
C188242C19
1.51,0.688 1.906,0.938 0.396,0.25 1.708,2.969 1.521,2.563 false 1.292,2.51 0.792,2.969 false 1.531,2.99 2.021,3.229 0.49,0.24 10 false CANP 0.51,3 0.979,3.198 0.469,0.198 10 false CANN 1.604,0.729 1.927,0.896 0.323,0.167 10 false d12 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-8 (CANP) - d12-7 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the position control ECU and switch assembly connector.


b.
C278316C05
1.448,0.271 1.917,0.552 0.469,0.281 1.5,2.865 1.969,3.146 0.469,0.281 0.865,4.448 1.156,4.115 false 0.656,3.292 1.146,3.615 false 2.313,2.521 2.083,2.156 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.573,0.313 2.031,0.563 0.458,0.25 10 false d12 1.635,2.917 1.979,3.135 0.344,0.219 10 false d11 2.198,2.583 2.813,2.781 0.615,0.198 10 false SYSB 0.323,3.177 0.771,3.385 0.448,0.208 10 false GND 0.646,4.438 0.958,4.635 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d11-2 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d11-7 (+B) - Body ground Power switch off 11 to 14 V
d12-12 (SYSB) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)