Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0232 Lost Communication with Blind Spot Monitor Slave Module No communication from the blind spot monitor sensor LH continues.
·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.

HINT:

This diagnosis procedure is for when DTC U0232 is output by the power management control ECU (Intelligent tester display: PM1 Gateway).


WIRING DIAGRAM

C240760E16
1.083,0.573 1.083,0.323 1.083,0.323 1.26,0.323 false 3.635,0.573 3.635,0.302 3.635,0.302 3.927,0.302 false 4.531,2.094 4.531,2.99 4.531,2.99 4.688,2.99 false 0.688,1.51 1.083,1.656 0.396,0.146 10 false 120 Ω 5.781,2.135 7.031,2.521 1.25,0.385 10 false Power Management Control ECU 6.146,1.51 6.542,1.656 0.396,0.146 10 false 120 Ω 2.188,2.771 2.646,2.917 0.458,0.146 10 false CA1P 1.875,4.313 3.781,4.49 1.906,0.177 10 false Blind Spot Monitor Sensor LH 4.219,4.396 5.125,4.583 0.906,0.188 10 false Trouble Area 2.281,2.583 2.531,2.729 0.25,0.146 10 false 8 2.917,2.583 3.177,2.729 0.26,0.146 10 false 4 2.052,3.979 2.479,4.167 0.427,0.188 10 false BLGD 2.042,3.375 2.354,3.552 0.313,0.177 10 false BLB 2.74,2.771 3.198,2.917 0.458,0.146 10 false CA1N 1.125,5 3.156,5.177 2.031,0.177 10 false : CAN Main Bus Line (CANH) 1.125,5.396 3.156,5.573 2.031,0.177 10 false : CAN Main Bus Line (CANL) 4.271,5 5.99,5.177 1.719,0.177 10 false : CAN Branch Line (CANH) 4.271,5.396 5.969,5.573 1.698,0.177 10 false : CAN Branch Line (CANL) 4.292,0.24 6.458,0.469 2.167,0.229 10 false CAN No. 3 Junction Connector 1.604,0.26 3.573,0.448 1.969,0.188 10 false CAN No. 4 Junction Connector 5.073,2.938 7.021,3.115 1.948,0.177 10 false CAN No. 2 Junction Connector 0.854,3.531 2.01,3.708 1.156,0.177 10 false ECU-IG1 NO. 3 1.552,4.313 1.875,4.49 0.323,0.177 10 false T10 1.885,3.865 2.01,4.042 0.125,0.177 10 false 1 1.896,3.271 2.031,3.448 0.135,0.177 10 false 5 1.292,0.26 1.594,0.448 0.302,0.188 10 false T16 3.979,0.24 4.302,0.427 0.323,0.188 10 false T15 4.729,2.927 5.031,3.115 0.302,0.188 10 false O30 5.594,2.135 5.792,2.323 0.198,0.188 10 false I3 0.042,0.01 1.156,0.323 1.115,0.313 12 false Sub Bus 11:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 11.68 seconds and then drive the vehicle at a speed of 5 km/h (3 mph) or more for at least 11.84 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > PM1 Gateway > Trouble Codes
50001 217
HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.



Result:
Result Proceed to
U1002 is not output from power management control ECU.
(Intelligent tester display: PM1 Gateway)
A
U1002 is output from power management control ECU.
(Intelligent tester display: PM1 Gateway)
B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.
C240531C01
0.406,1.615 0.927,1.927 0.521,0.313 2.063,1.771 2.583,1.771 false 1.99,1.99 1.99,2.583 1.99,2.583 2.177,2.583 false 0.125,0.063 0.333,0.26 0.208,0.198 10 *a 2.615,1.688 3.063,1.875 0.448,0.188 10 CA1N 2.219,2.49 2.646,2.677 0.427,0.188 10 CA1P 0.51,1.688 0.885,1.865 0.375,0.177 10 T10
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-8 (CA1P) - T10-4 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C240531C02
0.127,0.058 0.34,0.256 0.213,0.198 10 *a 0.413,2.178 0.866,2.365 0.453,0.187 10 BLGD 0.426,1.481 0.942,1.791 0.516,0.309 0.528,1.549 0.907,1.731 0.379,0.182 10 T10 1.496,1.743 0.937,2.233 false
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-1 (BLGD) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.
C240531C03
0.417,1.604 0.938,1.917 0.521,0.313 1.531,1.958 1.531,2.521 1.531,2.521 1.344,2.521 false 0.125,0.063 0.333,0.26 0.208,0.198 10 false *a 0.99,2.427 1.333,2.615 0.344,0.188 10 false BLB 0.521,1.677 0.896,1.854 0.375,0.177 10 false T10
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-5 (BLB) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)