Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  U0293  Lost Communication with HV ECU  


DESCRIPTION

This DTC is stored when the power management control ECU detects a CAN communication error inside the power management control ECU (power control section - HV control section).

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0293 Lost Communication with HV ECU CAN communication error inside the power management control ECU (power control section - HV control section). (1-trip detection logic*)
·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation

Turn the power switch on (IG) and wait 10 seconds or more.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
There is no effect on vehicle behavior. -

WIRING DIAGRAM

B275476E11
1.156,3.406 3.031,3.688 1.875,0.281 10 false : CAN Communication Line 2.583,2.052 2.958,2.344 0.375,0.292 10 false I4 2.583,1.625 2.885,1.854 0.302,0.229 10 false I4 1.365,0.927 1.927,1.26 0.563,0.333 10 false AM2 0.146,0.771 1.031,1.323 0.885,0.552 10 false from Auxiliary Battery 2.563,1.875 2.833,2.052 0.271,0.177 10 false 25 2.563,1.438 2.844,1.74 0.281,0.302 10 false 24 2.875,1.948 3.417,2.24 0.542,0.292 10 false CA1H 3.438,3.094 5.75,3.521 2.313,0.427 10 false Power Management Control ECU 2.875,1.521 3.406,1.781 0.531,0.26 10 false CA1L 5.698,0.771 6.125,1.083 0.427,0.313 10 false E01 5.698,1.188 6.115,1.427 0.417,0.24 10 false E02 5.698,2.021 6.115,2.281 0.417,0.26 10 false E12 5.76,1.615 6.115,1.979 0.354,0.365 10 false E1 3.885,1.688 5.458,1.948 1.573,0.26 10 false Power Control Section 4.021,2.354 5.219,2.521 1.198,0.167 10 false HV Control Section 6.167,0.594 6.438,0.854 0.271,0.26 10 false 5 6.146,0.771 6.417,0.958 0.271,0.188 10 false I3 6.167,1 6.396,1.219 0.229,0.219 10 false 5 6.156,1.188 6.427,1.375 0.271,0.188 10 false I4 6.156,1.427 6.479,1.719 0.323,0.292 10 false 6 6.135,1.615 6.49,1.885 0.354,0.271 10 false I3 6.156,1.833 6.271,1.979 0.115,0.146 10 false 4 6.146,2.01 6.417,2.198 0.271,0.188 10 false I4 2.875,0.781 3.417,1.135 0.542,0.354 10 false AM21 2.594,0.573 2.875,0.906 0.281,0.333 10 false 7 2.583,0.771 2.792,0.958 0.208,0.188 10 false I4 2.875,1.188 3.479,1.521 0.604,0.333 10 false AM22 2.594,1 2.917,1.323 0.323,0.323 10 false 1 2.583,1.188 2.854,1.375 0.271,0.188 10 false I3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
U0293 - -


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Clear DTCs
50002 223

b.

Check for DTCs again.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC U0293 is not output



Result:
Proceed to
OK
NG



OK

NG