Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2012.02–2014.05
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2282 Vehicle Speed Signal Malfunction The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Meter/gauge system

·

Power management control ECU

·

Junction Connector

·

Wire harness or connector


DTC Output Confirmation Operation

Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.


B2283 Vehicle Speed Sensor Malfunction Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
·

AM2 fuse

·

Meter/gauge system

·

Power management control ECU

·

Junction Connector

·

Wire harness or connector


DTC Output Confirmation Operation

Drive the vehicle for 30 seconds or more at a vehicle speed of 50 km/h (31 mph) or more.



*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power switch cannot be turned from on (IG) to off.


-
B2283
·

The power source mode is changed to off (the hybrid control system is stopped) by pressing the power switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start.


Steering lock operation is prohibited.

WIRING DIAGRAM

B309632
0.434,1.364 1.557,1.515 1.123,0.151 10 Skid Control ECU 1.001,0.521 1.292,0.672 0.292,0.151 10 SP1 0.1,1.364 0.419,1.545 0.319,0.181 10 A28 0.617,5.091 2.388,5.415 1.772,0.324 10 Stereo Component Amplifier Assembly*2 0.324,5.091 0.643,5.271 0.319,0.181 10 I69 1.369,0.521 1.556,0.669 0.187,0.148 10 11 2.943,3.006 3.123,3.164 0.180,0.159 10 21 3.959,3.006 4.138,3.164 0.180,0.159 10 18 3.959,4.682 4.138,4.840 0.180,0.159 10 17 2.943,6.158 3.123,6.317 0.180,0.159 10 20 5.39,0.521 5.694,0.671 0.304,0.150 10 8 5.391,3.006 5.666,3.155 0.275,0.150 10 9 5.611,0.605 5.810,0.755 0.198,0.150 10 SI 5.605,3.104 5.806,3.255 0.201,0.151 10 +S 4.999,3.451 5.294,3.597 0.295,0.145 10 I18 5.271,3.451 7.107,3.607 1.835,0.156 10 Combination Meter Assembly 5.582,4.682 5.911,4.827 0.328,0.145 10 SPD 5.32,4.682 5.632,4.843 0.311,0.162 10 17 5.582,6.181 5.911,6.326 0.328,0.145 10 SPD 5.306,6.181 5.492,6.342 0.186,0.162 10 17 4.803,6.552 5.274,6.714 0.471,0.162 10 I67 5.044,6.552 7.132,6.743 2.088,0.190 10 Navigation ECU Sub-assembly*2 2.943,4.682 3.123,4.840 0.180,0.159 10 19 1.661,4.682 1.989,4.827 0.328,0.145 10 SPD 2.115,4.682 2.287,4.843 0.172,0.162 10 11 4.266,5.07 4.570,5.229 0.304,0.159 10 I155 4.616,5.07 7.129,5.257 2.513,0.187 10 Radio and Display Receiver Assembly*1 3.083,6.57 4.303,6.732 1.220,0.162 10 Junction Connector 2.743,6.57 3.143,6.734 0.400,0.164 10 I124 2.115,6.165 2.426,6.327 0.311,0.162 10 24 0.327,6.57 2.473,6.746 2.146,0.176 10 Windshield Wiper Relay Assembly 0.287,7.278 2.787,7.454 2.500,0.176 10 *1: for Radio and Display Receiver Type 3.089,7.278 5.110,7.454 2.021,0.176 10 *2: for Navigation Receiver Type 1.661,6.165 1.989,6.310 0.328,0.145 10 SPD 0.056,6.57 0.334,6.723 0.277,0.153 10 I72 0.577,3.608 2.758,3.771 2.182,0.164 10 Power Management Control ECU 1.966,2.946 2.367,3.100 0.400,0.154 10 SPDI 2.423,2.914 2.603,3.072 0.180,0.159 10 14 4.099,2.27 5.453,2.448 1.354,0.178 10 from Auxiliary Battery 3.165,2.42 3.495,2.611 0.330,0.191 10 AM2 1.937,2.259 2.377,2.408 0.441,0.149 10 AM21 2.478,2.098 2.589,2.243 0.111,0.145 10 7 2.464,2.27 2.670,2.461 0.206,0.191 10 I4 1.937,2.665 2.377,2.814 0.441,0.149 10 AM22 2.478,2.49 2.589,2.636 0.111,0.145 10 1 2.464,2.676 2.737,2.867 0.272,0.191 10 I3 0.914,2.11 1.355,2.259 0.441,0.149 10 E01 0.634,1.924 0.745,2.070 0.111,0.145 10 5 0.62,2.11 0.892,2.301 0.272,0.191 10 I3 0.921,2.51 1.362,2.659 0.441,0.149 10 E02 0.641,2.323 0.752,2.469 0.111,0.145 10 5 0.627,2.51 0.899,2.700 0.272,0.191 10 I4 0.9,2.895 1.341,3.044 0.441,0.149 10 E1 0.62,2.709 0.731,2.854 0.111,0.145 10 6 0.606,2.895 0.878,3.086 0.272,0.191 10 I3 0.907,3.294 1.348,3.443 0.441,0.149 10 E12 0.627,3.108 0.738,3.253 0.111,0.145 10 4 0.613,3.294 0.885,3.485 0.272,0.191 10 I4 2.458,3.098 2.730,3.288 0.272,0.191 10 I3 2.857,1.14 4.638,1.339 1.781,0.199 10 CAN Communication Line

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in an ECU, all systems in the diagram above will not operate normally.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Engine Condition

·

Power Supply Condition


Combination Meter
·

Vehicle Speed Meter


-


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the Data List for proper functioning of the vehicle speed signal.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed (Speedometer tester) -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8

OK:

Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

2.READ VALUE USING INTELLIGENT TESTER
a.

Enter the following menus: Body / Power Source Control / Data List.


b.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Speed Signal
50003 223 16
OK:

Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the I3 connector from the power management control ECU.


b.

Disconnect the I18 connector from the combination meter assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-14 (SPDI) - I18-9 (+S) Always Below 1 Ω
I3-14 (SPDI) or I18-9 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK POWER MANAGEMENT CONTROL ECU

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
6.CHECK POWER MANAGEMENT CONTROL ECU
B294201C12
1.792,0.344 2.25,0.625 0.458,0.281 1.792,1.042 1.396,1.865 false 1.885,1.115 1.938,1.865 false 1.302,1.865 1.49,2.021 0.188,0.156 10 false E1 1.781,1.875 2.125,2.031 0.344,0.156 10 false SPDI 1.948,0.396 2.219,0.552 0.271,0.156 10 false I3 0.083,0.094 0.271,0.25 0.188,0.156 10 false *a 2.75,3.646 3.073,3.802 0.323,0.156 10 false GND
*a Component with harness connected(Power Management Control ECU)


a.

Reconnect the I3 power management control ECU connector.


b.

Reconnect the I18 combination meter assembly connector.


c.

Connect an oscilloscope to terminal I3-14 (SPDI) and I3-6 (E1).


d.

Turn the power switch on (IG).


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection I3-14 (SPDI) - I3-6 (E1)
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

The wavelength becomes shorter as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I124 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-9 (+S) - I124-18 Always Below 1 Ω
I18-9 (+S) or I124-18 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-14 (SPDI) - I124-21 Always Below 1 Ω
I3-14 (SPDI) or I124-21 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR