Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075062 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high, the power management control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*).
·

Wire harness or connector (disconnection or break in wire harness is main cause)

·

Certification ECU (smart key ECU assembly)

·

Power management control ECU


DTC Output Confirmation Operation

Turn the power switch on (IG) and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B271007E08
0.803,1.795 1.006,1.969 0.204,0.174 10 I4 0.803,1.96 2.103,2.297 1.301,0.338 10 Power Management Control ECU 5.5,0.986 5.852,1.16 0.352,0.174 10 EFIO 1.497,0.986 1.722,1.16 0.225,0.174 10 IMI 5.222,0.9 5.492,1.074 0.27,0.174 10 14 1.797,0.9 2.067,1.074 0.27,0.174 10 21 5.179,1.801 5.468,1.975 0.289,0.174 10 I87 5.179,1.951 6.764,2.258 1.585,0.307 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the power switch on (IG) and wait 10 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC B279A is output. A
DTC B279A and other DTCs are output. B


HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the power management control ECU and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER MANAGEMENT CONTROL ECU)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the I87 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I4 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-14 (EFIO) - I4-21 (IMI) Always Below 1 Ω
I4-21 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I4-21 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE POWER MANAGEMENT CONTROL ECU