Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075086 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 89860 1.INSTALL SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256C05
5.01,0.51 5.292,0.792 0.281,0.281 10 false *b 1.792,0.51 2.063,0.792 0.271,0.281 10 false *a
*a Correct *b Incorrect



d.

Insert the pin (stopper) into the body hole and install the side airbag sensor assembly to the vehicle body with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

B286418C02
2.104,1.948 1.948,1.76 1.948,1.76 1.802,1.76 false 3.813,2.021 3.646,1.854 3.646,1.854 3.51,1.854 false 4.021,2.063 4.281,2.063 false 5.656,2.125 5.917,2.125 false 4.313,1.969 4.531,2.156 0.219,0.188 10 false *1 3.813,2.427 4.01,2.635 0.198,0.208 10 false *a 1.594,1.667 1.844,1.896 0.25,0.229 10 false (A) 3.302,1.76 3.531,1.948 0.229,0.188 10 false (A) 5.958,2.031 6.146,2.229 0.188,0.198 10 false *1
*1 White Housing Lock - -
*a Slide - -


NOTICE:
·

If the side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.




e.

Connect the connector to the side airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the side airbag sensor assembly.


Hide 62413A 2.INSTALL CENTER PILLAR LOWER GARNISH

Hide 62331A 3.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67917A 4.INSTALL REAR DOOR SCUFF PLATE

Hide 62311B 5.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67913 6.INSTALL FRONT DOOR SCUFF PLATE

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 64718C 8.INSTALL LUGGAGE TRIM SERVICE HOLE COVER