Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075122 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.
E230595

When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 120 to 135 cc (4.2 to 4.8 fl. oz.)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, observe the precautions on the cooler removal/installation.

·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 or equivalent is used, the compressor with motor assembly insulation performance may decrease, resulting in a leakage of electric power.




Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.

Using an E8 "TORX" socket, install the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
E230594E03
0.958,0.49 1.365,0.49 false 0.74,0.385 1.104,0.698 0.365,0.313 10 false (1) 1.875,1.677 2.323,1.938 0.448,0.26 10 false (2) 1.302,1.531 1.688,1.823 0.385,0.292 10 false (3)

Install the compressor with motor assembly with the bolt and 2 nuts.

HINT:

Tighten the 2 bolts and nut in the order shown in the illustration.


Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


c.
E248802C01
1.688,0.24 1.365,0.458 false 0.698,2.625 1.26,2.625 false 1.698,0.104 2.104,0.406 0.406,0.302 10 false *1 2.208,2 2.698,2.344 0.49,0.344 10 false <A> 0.396,2.521 0.823,2.813 0.427,0.292 10 false <B>
*1 Green-colored Lock


Connect the connector <B>.


d.

Connect the connector <A> and slide the green-colored lock in the direction indicated by the arrow in the illustration to lock it securely.

CAUTION:

Make sure to wear insulating gloves.


NOTICE:

Make sure that the connector is connected securely.



Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:
·

Keep the O-ring and O-ring fitting surfaces free of foreign matter.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, the compressor with motor assembly insulation performance may decrease, resulting in a leakage of electric power.




d.

Install the suction hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:
·

Keep the O-ring and O-ring fitting surfaces free of foreign matter.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, the compressor with motor assembly insulation performance may decrease, resulting in a leakage of electric power.




d.

Install the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 5.INSTALL RADIATOR ASSEMBLY

Hide 7. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT