Home › Engine / Hybrid System › 2AR-FXE COOLING › RADIATOR › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014697 2AR-FXE COOLING _0074934 RADIATOR A

2AR-FXE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16400 1.INSTALL RADIATOR ASSEMBLY

a.
A259368C01
1.628,2.02 1.827,2.166 0.199,0.146 10 *a 1.111,1.926 1.597,2.084 false 2.264,1.929 1.808,2.085 false
*a Guide


Install the fan assembly to the radiator with the 2 guides at the bottom and 3 claws on the top.


b.

Install the 2 lower radiator supports to the radiator assembly.


c.
A268142

Install the radiator with fan assembly.

NOTICE:

Do not apply any excessive force to the radiator assembly (for inverter coolant), cooler condenser assembly or pipe when installing the radiator assembly.



d.

Install the radiator with fan assembly to the condenser assembly and radiator assembly (for inverter coolant) with the 4 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the No. 4 inverter cooling hose with the clamp.


f.

Connect the connector and the 2 clamps.


g.

Connect the 2 clamps.


Hide 53216A 2.INSTALL UPPER RADIATOR SUPPORT

a.

Install the 2 radiator support cushions to the radiator assembly.


b.

Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Connect the connector.


Hide G9170 4.CONNECT NO. 1 INVERTER COOLING PIPE ASSEMBLY

a.
A306186N01
1.208,0.49 1.365,0.688 0.156,0.198 10 false A 2.688,1.031 2.844,1.229 0.156,0.198 10 false B

Temporarily install the bolt A.


b.

Install the bolt B.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Fully tighten the bolt A.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 16572D 5.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose and clamp.


Hide 16571C 6.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose.


Hide 16470 7.INSTALL RADIATOR RESERVE TANK ASSEMBLY

a.

Install the radiator reserve tank with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the radiator reserve tank hose.


Hide 17750A 9.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53111 10.INSTALL RADIATOR GRILLE SUB-ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 12.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 14.INSPECT FOR COOLANT LEAK (for Engine)

Hide 53295E 15.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 51442C 16.INSTALL ENGINE UNDER COVER LH

Hide 51441C 17.INSTALL ENGINE UNDER COVER RH

Hide 53852K 18.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851Z 19.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH