Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.02–2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Back-up Light Circuit  


DESCRIPTION

The power management control ECU controls the back-up lights via the engine room junction block assembly.

WIRING DIAGRAM

E228416E03
3.417,1.429 3.744,1.603 0.328,0.174 10 ALT 3.417,2.129 3.855,2.303 0.439,0.174 10 GND1 3.417,2.523 3.855,2.697 0.439,0.174 10 GND2 4.072,2.535 4.483,2.709 0.411,0.174 10 BKLP 4.072,0.948 4.483,1.122 0.411,0.174 10 BLPS 2.673,2.955 5.179,3.141 2.506,0.186 10 Engine Room Junction Block Assembly 3.417,0.94 3.864,1.114 0.448,0.174 10 BATT 0.437,1.432 1.583,1.606 1.145,0.174 10 from DC/DC Fuse 0.206,0.942 1.581,1.116 1.375,0.174 10 from Auxiliary Battery 5.476,5.412 6.752,5.744 1.276,0.332 10 Power Management Control ECU 5.476,5.253 5.759,5.427 0.283,0.174 10 A38 3.083,0.94 3.212,1.114 0.129,0.174 10 A 3.091,0.753 3.261,0.927 0.171,0.174 10 1 3.052,2.129 3.265,2.303 0.212,0.174 10 1F 3.091,1.94 3.261,2.115 0.171,0.174 10 3 3.083,1.429 3.254,1.603 0.171,0.174 10 B 3.091,1.242 3.185,1.417 0.094,0.174 10 1 4.647,0.948 4.874,1.122 0.226,0.174 10 1F 4.686,0.749 4.857,0.924 0.171,0.174 10 9 5.816,0.936 6.056,1.111 0.240,0.174 10 BL 5.566,0.847 5.764,1.022 0.198,0.174 10 15 4.619,2.535 4.855,2.709 0.235,0.174 10 1M 4.672,2.348 4.766,2.522 0.094,0.174 10 1 3.052,2.523 3.278,2.697 0.226,0.174 10 1G 3.091,2.336 3.185,2.511 0.094,0.174 10 4 3.211,4.07 4.767,4.402 1.557,0.332 10 Rear Light Assembly LH (Back-up Light) 3.211,3.911 3.496,4.086 0.285,0.174 10 T18 3.211,5.422 4.788,5.754 1.577,0.332 10 Rear Light Assembly RH (Back-up Light) 3.211,5.263 3.505,5.437 0.294,0.174 10 T17 3.256,3.546 3.350,3.720 0.094,0.174 10 1 4.518,3.546 4.631,3.720 0.113,0.174 10 2 3.256,4.898 3.350,5.072 0.094,0.174 10 1 3.405,3.546 3.543,3.720 0.138,0.174 10 E 3.405,4.898 3.543,5.072 0.138,0.174 10 E 4.342,4.898 4.482,5.072 0.140,0.174 10 B 4.342,3.546 4.482,3.720 0.140,0.174 10 B 4.518,4.898 4.631,5.072 0.113,0.174 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL SYSTEM)
a.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236
OK:

Hybrid control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

E230000C11
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.615,3.688 2.552,4.135 false 6.281,3.625 6.219,3.948 false 2.865,2.635 3.271,2.896 0.406,0.26 10 1F 4.802,2.729 5.469,3.125 0.667,0.396 10 1G 6.302,3.115 6.75,3.438 0.448,0.323 10 A 0.875,3.094 1.406,3.469 0.531,0.375 10 B 0.271,0.208 0.688,0.552 0.417,0.344 10 *a 6.083,3.958 6.781,4.323 0.698,0.365 10 BATT 5.115,4 5.823,4.333 0.708,0.333 10 GND2 2.344,4.167 3.24,4.542 0.896,0.375 10 GND1 0.646,3.927 1.5,4.344 0.854,0.417 10 ALT
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Power switch off 11 to 14 V
B-1 (ALT) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY))
a.

Disconnect the T18 rear light assembly LH connector.


b.

Disconnect the T17 rear light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side
Tester Connection Condition Specified Condition
1M-1 (BKLP) - T18-2 (B) Always Below 1 Ω

RH Side
Tester Connection Condition Specified Condition
1M-1 (BKLP) - T17-2 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A38 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-9 (BLPS) - A38-15(BL) Always Below 1 Ω
1F-9 (BLPS) - Bodyground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Replace the engine room junction block assembly with a new or a known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL

OK:

The back-up lights operate normally.



Result:
Proceed to
OK
NG



OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG