Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM2040EQ _59 Vehicle Exterior _014740 EXTERIOR PANELS / TRIM _0075196 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  INSTALLATION  


PROCEDURE

Hide 75754A 1.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

a.
B280099

Engage the claw and guide of the front door upper window frame moulding to the door frame.


b.

Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C15
1.333,0.24 1.479,0.24 1.479,0.24 1.802,0.719 false 1.854,1.26 1.854,1.781 false 2.333,0.052 2.531,0.208 0.198,0.156 10 false *a 1.115,0.135 1.302,0.292 0.188,0.156 10 false *1 1.76,1.781 1.938,1.938 0.177,0.156 10 false *2
*1 Riveter
*2 Mandrel
*a Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C13
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 2.323,0.083 2.5,0.24 0.177,0.156 10 false *a 2.333,1.094 2.521,1.25 0.188,0.156 10 false *a 1.458,0.354 1.948,0.51 0.49,0.156 10 false *1 1.479,1.333 1.969,1.49 0.49,0.156 10 false *1
*1 Riveter
*a Incorrect


Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

·
B125585C12
1.156,0.75 1.417,0.75 false 2.448,0.313 2.76,0.615 0.313,0.302 10 false *a 1.438,0.677 1.917,1.01 0.479,0.333 10 false *1
*1 Riveter
*a Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 75756C 2.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

When installing a new front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or front door rear window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B280096C08
2.781,1.042 2.479,1.271 false 2.031,1.781 2.396,1.854 false 2.76,3.188 2.521,2.844 false 1.865,1.677 2.188,1.958 0.323,0.281 10 false *1 2.823,0.927 3.104,1.167 0.281,0.24 10 false *1 2.719,3.219 3.042,3.427 0.323,0.208 10 false *2
*1 Double-sided Tape
*2 Caulking Sponge


Install a new front door rear window frame moulding.

i.

Using a heat light, heat the vehicle body and front door rear window frame moulding.


ii.

Remove the release paper from the face of the front door rear window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front door rear window frame moulding with the clip.



Hide 67862 3.INSTALL FRONT DOOR WEATHERSTRIP

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>REASSEMBLY


Hide 68620 4.INSTALL FRONT DOOR CHECK ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>REASSEMBLY


Hide 68151C 5.INSTALL FRONT DOOR GLASS RUN

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>REASSEMBLY


Hide 75720 6.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY