Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2040EQ _59 Vehicle Exterior _014735 DOOR / HATCH _0075151 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75975G 3.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>INSTALLATION


Hide 75985B 4.INSTALL FRONT DOOR STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>INSTALLATION


Hide 75753 5.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 75755C 6.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 75710 7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION


Hide 67481C 8.INSTALL FRONT DOOR FRONT LOWER FRAME SEAL

a.
B286927

Install front door front lower frame seal.


Hide 67001A 9.INSTALL FRONT DOOR PANEL CUSHION

a.
B307960

Engage the 2 claws to install 2 new front door panel cushions.


Hide 67863B 10.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP

a.
B286925

Engage the 8 clips to install the front door No. 2 weatherstrip.


Hide 67663D 11.INSTALL DOOR FRAME GARNISH

a.
B286924

Engage the clip to install a new door frame garnish.


Hide 67861 12.INSTALL FRONT DOOR WEATHERSTRIP

a.
B307959

Engage the 19 clips and install the front door weatherstrip.


Hide 68610B 13.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
B286922E02
0.333,1.104 0.563,1.292 0.229,0.188 10 true (A) 1.333,0.74 1.563,0.927 0.229,0.188 10 false (B) 1.219,1.396 1.448,1.583 0.229,0.188 10 false (B)

Install the front door check assembly with the 3 bolts.

Torque:
Bolt (A) : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 69311A 14.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B286928N03
0.417,0.688 0.625,0.875 0.208,0.188 10 false (1) 1.198,0.667 1.406,0.854 0.208,0.188 10 true (2)

Install the front door lock open rod as indicated by the arrows and in the order shown in the illustration.


Hide 82185A 15.INSTALL FRONT DOOR SMART WIRE

a.
B286920

Engage the 3 clamps to install the front door smart wire.


Hide 69201A 16.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B307961C01
0.044,0.015 0.219,0.183 0.175,0.168 10 *a 0.044,2.112 0.219,2.280 0.175,0.168 10 *b 3.136,1.351 3.291,1.505 0.155,0.155 10 *1 2.73,1.485 3.122,1.452 false
*1 Door Handle Nut
*a Outside
*b Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw and door handle nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.
B286918

Engage the 3 clamps.


e.

Connect the connector.


Hide 69750C 17.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B286930

Install the front door inside locking cable assembly.


b.
B286916

Engage the 3 claws.


Hide 69710B 18.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B286931

Install the front door lock remote control cable assembly.


Hide 69030A 19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly:

i.
B286914

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.
B286932C04
0.155,2.677 0.318,2.84 0.163,0.163 10 *1 0.462,2.63 0.325,2.747 false
*1 Front Door Lock Open Rod


Insert the front door lock open rod to the front door lock with motor assembly.


d.

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.


e.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 69242E 20.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B307957

Engage the 2 claws to install the front door rear outside handle pad.


Hide 69241H 21.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B307956

Engage the 3 claws to install the front door front outside handle pad.


Hide 69220 22.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B307962

Insert the front end of the front door outside handle assembly into the front door outside handle frame.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B286909

Connect the connector.


d.

Engage the 2 claws.


Hide 69250B 23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B286934

Engage the 2 guides and claw, and install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.


Hide 69217F 24.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B307954

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B286907

Install the hole plug.


Hide 25.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B307953

Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B286904

Install the hole plug.


Hide 67403F 26.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B307963

Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the 2 bolts.


Hide 67401F 27.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B286937

Engage the guide as shown in the illustration.


b.

Install the front door front lower frame sub-assembly with the 2 bolts.


Hide 68141C 28.INSTALL FRONT DOOR GLASS RUN

a.
B307951

Install the front door glass run.


Hide 67923 29.INSTALL NO. 1 FRONT DOOR STIFFENER CUSHION

a.

Clean the front door panel sub-assembly.


b.
B286900C03
2.051,1.204 2.221,1.364 0.169,0.16 10 *1 1.153,1.295 2.035,1.295 false
*1 Double-sided Tape


Engage the 2 guides.


c.

Install a new No. 1 front door stiffener cushion with the 2 bolts.


Hide 85710E 30.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.


a.
B286899

Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 31.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Install the temporary bolt to the front door window regulator assembly.


c.
B307950C02
1.531,0.813 1.792,0.167 false 1.813,0.063 1.958,0.219 0.146,0.156 10 false *1 1.208,1.302 1.417,1.49 0.208,0.188 10 true (1) 0.667,0.854 0.875,1.042 0.208,0.188 10 true (2) 0.854,1.302 1.063,1.49 0.208,0.188 10 true (3) 1.99,0.052 2.198,0.24 0.208,0.188 10 false (4) 2.24,1.125 2.5,1.333 0.26,0.208 10 true (5) 1.552,1.156 1.76,1.344 0.208,0.188 10 true (6)
*1 Temporary Bolt


Temporarily install the front door window regulator assembly.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 68101 32.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Disconnect the power window regulator master switch assembly.


e.
B307964E01
1.914,0.038 2.115,0.224 0.200,0.186 10 (1) 2.572,0.063 2.773,0.249 0.200,0.186 10 (2)

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows and in the order shown in the illustration.


f.
B307948

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
B307947

Install the grommet.


Hide 67831 33.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.
B314412C01
1.454,0.125 1.633,0.277 0.179,0.152 10 *1 1.921,0.109 2.101,0.260 0.179,0.152 10 *1 0.924,3.06 1.103,3.212 0.179,0.152 10 *1 0.901,3.111 0.538,2.922 false 1.134,0.213 1.442,0.213 false 2.559,0.188 2.123,0.188 false
*1 Reference Point


Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.

Attach the front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



d.

Engage the 3 clamps.


e.

Connect each connector.


Hide 89430 34.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 35.INSTALL MIRROR SUB-ASSEMBLY WITH COVER

Hide 86160 36.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 84927 37.INSTALL SEAT MEMORY SWITCH (w/ Memory)

Hide 68171B 38.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B286940

Install the front door inner glass weatherstrip.


Hide 69205 39.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B286892

Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 67601 40.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B286941C02
0.604,0.813 0.979,1.042 false 1.146,1.594 1.073,1.25 false 0.458,0.719 0.625,0.885 0.167,0.167 10 false *1 1.083,1.625 1.271,1.813 0.188,0.188 10 false *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.
B314413C01
2.845,4.128 3.006,4.283 0.161,0.155 10 *1 2.541,4.203 2.817,4.214 false
*1 Reference Boss


Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.


c.
B314410

Engage the 10 clips.


d.

Install the 3 screws to install to front door trim board sub-assembly.


e.

If protective tape has been applied, remove it.


Hide 81911B 41.INSTALL REFLEX REFLECTOR

a.
B293480C02
0.199,0.129 0.411,0.31 0.212,0.181 10 *A 0.199,2.384 0.411,2.565 0.212,0.181 10 *B
*A for LH Side
*B for RH Side


Engage the claw to install the front reflex reflector assembly.


Hide 74210 42.INSTALL FRONT ARMREST ASSEMBLY

a.
B286943

Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.


Hide 43.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect each connector.


b.
B307013

Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.


Hide 44.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B286945

Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.


Hide 67491A 45.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B286884

Engage the 3 clips to install the front door lower frame bracket garnish.


Hide 69283 46.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B286946

Engage the 3 claws to install the front door inside handle bezel plug.


Hide 47.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 48.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 49.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

Hide 51.INSPECT POWER SEAT OPERATION (w/ Memory)