Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM
RM2040EQ _58 Vehicle Interior _014732 INTERIOR PANELS / TRIM _0075134 REAR SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  Rear Sunshade Shift-linked Function does not Operate when Shift Lever is Moved to R Position  


DESCRIPTION

When the power switch is on (IG) and the shift lever is moved to R, the shift lever position sensor sends a reverse (R) signal to the power management control ECU. Then, the power management control ECU sends this signal to the main body ECU (multiplex network body ECU) via CAN. When the rear sunshade relay (rear window shade assembly) receives this signal with the rear sunshade raised, the rear sunshade is lowered.

WIRING DIAGRAM

B235132E28
0.781,2.396 2.708,2.646 1.927,0.25 10 false : CAN Communication Line 0.917,1.865 2.177,2.25 1.26,0.385 10 false Power Management Control ECU 2.802,1.906 4.448,2.333 1.646,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 4.875,1.906 6.594,2.375 1.719,0.469 10 false Rear Sunshade Relay (Rear Window Shade Assembly) 2.802,1.74 3.177,1.979 0.375,0.24 10 false I13 4.875,1.75 5.365,2.063 0.49,0.313 10 false N19 5.271,0.938 5.594,1.083 0.323,0.146 10 false REV 3.75,0.938 4.26,1.198 0.51,0.26 10 false REV 3.146,0.938 3.615,1.24 0.469,0.302 10 false CAN 1.677,0.938 2.156,1.167 0.479,0.229 10 false CAN 5.073,0.833 5.292,1.052 0.219,0.219 10 false 3 4.135,0.833 4.552,1.073 0.417,0.24 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

Since the rear sunshade system has functions that use CAN communication, first confirm that there is no malfunction in the CAN communication system using the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>INTERIOR PANELS / TRIM>REAR SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Sensor SW - R Shift lever position sensor ON or OFF ON: Shift lever in R
OFF: Shift lever in any position other than R
-
OK:

The intelligent tester display changes according to the shift state selected using the shift lever.


Powertrain > Hybrid Control > Data List
Tester Display
Shift Sensor SW - R
50003 236 71

Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

HINT:

Make sure the rear window shade assembly is raised before performing Active Test.


Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Reverse Gear Signal Reverse signal OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Reverse Gear Signal
50004 123 24

OK:

The rear window shade assembly is lowered.


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
3.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N19-3 (REV) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
4.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-3 (REV) - I13-15 (REV) Always Below 1 Ω
I13-15 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR