When the vehicle doors are unlocked through wireless unlock or entry unlock operation, the certification ECU (smart key ECU assembly) sends the key ID signal and smart memory call request signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the signal and the driver door is opened, the ECU sends the memory call command signal for the received key ID to each outer mirror control ECU assembly. On receiving the memory call command signal, each outer mirror control ECU assembly moves the mirror surface to the stored position.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.
With the power switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter transmitter key recognition code registration mode to allow a key to be linked to mirror surface memory position.
If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7* |
- |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
The Data List shows that the key ID has been linked to a switch (M1 or M2).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
| Result | Proceed to |
|---|---|
| The memory call function does not operate together with wireless door unlock operation only. | A |
| The memory call function does not operate together with entry unlock operation only. | B |
| The memory call function does not operate at all. | C |
A
B
C
Check wireless door lock control operation.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Wireless door lock control operation is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check memory and seat restoring operation.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory and seat restoring operations are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration for memory call function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Driver door courtesy switch condition | ON or OFF | ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed) |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
ON or OFF appears on the intelligent tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform a wireless door unlock operation and check that opening the driver side door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the smart entry and start system operation.
Smart entry and start system operation is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check memory and seat restoring operation.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory and seat restoring operations are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration for memory call function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Driver door courtesy switch condition | ON or OFF | ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed) |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
ON or OFF appears on the intelligent tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration for memory call function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Turn to Left Fully |
Turn the power switch on (IG).
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
| *a | Turn to Right Fully |
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.
Mirror function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration for memory call function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check electrical remote control mirror function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Electrical remote control mirror function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>PROBLEM SYMPTOMS TABLE
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Driver door courtesy switch condition | ON or OFF | ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed) |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
ON or OFF appears on the intelligent tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration for memory call function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG