Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1290/66  Steering Angle Sensor Zero Point Malfunction  


DESCRIPTION

The skid control ECU acquires the steering angle sensor zero point every time the power switch is turned on (READY) and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The skid control ECU also stores the previous zero point.

If the front wheel alignment or the steering wheel position is adjusted without disconnecting the cable from the negative (-) auxiliary battery terminal, or if yaw rate and acceleration sensor zero point is not acquired after the adjustments have been completed, the skid control ECU detects the difference between the previous zero point and newly acquired zero point and stores this DTC to indicate a poor adjustment.

The warning of the steering angle sensor zero point malfunction will be canceled by turning the power switch off.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1290/66 Steering Angle Sensor Zero Point Malfunction 751 The steering angle sensor zero point is judged as an abnormal value.
·

Yaw rate and acceleration sensor zero point calibration incomplete

·

Poor adjustment of the center position of the steering wheel

·

Poor adjustment of front wheel alignment


VSC DTC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 166
HINT:
·

When the stored zero point of the yaw rate and acceleration sensor is cleared, steering angle sensor zero point will also be cleared.

·

If the zero point and output value of the yaw rate and acceleration sensor and the output value of the speed sensors are not normal, steering angle sensor zero point cannot be acquired normally even if the vehicle is driven straight ahead at 35 km/h (22 mph) or more.




Result:
Proceed to
NEXT



NEXT

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Turn the power switch off.


b.

Turn the power switch on (READY).


c.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


d.

Check that the steering wheel is centered correctly while driving straight ahead.

HINT:

If front wheel alignment and steering position are adjusted as a result of the steering wheel being off-center, acquire yaw rate and acceleration sensor zero point again after the adjustments are completed.


OK:

The steering wheel is centered correctly.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION

3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (22 mph) or more.


e.

Check if the same DTC is stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1290/66 is not output. A
DTC C1290/66 is output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY