Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.02–2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1380/64  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop lights come on.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1380/64 Stop Light Control Relay Malfunction 761
762
·

INF Code: 761

·

When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 terminal for 2 seconds or more.



·

INF Code: 762

·

When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more.



·

Stop light switch assembly circuit

·

Stop light control relay (STOP relay)

·

Stop light control relay (STOP relay) circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


VSC DTC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1249/49


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY)

NG

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY)
a.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (STOP relay) Relay ON/OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

b.

Perform the Active Test of the stop light control relay (STOP relay) using the intelligent tester.


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (STOP relay) output ON or OFF ON: Relay output on
OFF: Relay output off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Relay Output
50003 105 291

d.

Check for stop light control relay (STOP relay) operation using the Data List and stop light operation by performing the Active Test.


Result:
Result Proceed to
Data List content and stop light operation are normal. A
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. B



A

4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

B

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C249762C48
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.656 2.302,0.771 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A28 2.333,0.688 2.74,0.896 0.406,0.208 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-6 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A28-6 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1380/64 is not output. A
DTC C1380/64 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C244747C05
1.031,1.865 0.74,1.865 false 0.25,0.198 0.615,0.573 0.365,0.375 10 false *1 0.552,1.771 0.927,2.052 0.375,0.281 10 false *2
*1 No. 2 Engine Room Relay Block
*2 Stop Light Control Relay (STOP Relay)


Turn the power switch off.


b.

Remove the stop light control relay (STOP relay).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control relay (STOP relay) terminal 5 - Body ground Always 11 to 14 V
Stop light control relay (STOP relay) terminal 2 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)
a.
C223784C11
0.284,0.252 0.532,0.446 0.249,0.193 10 *1 2.714,1.412 2.714,0.86 2.714,0.86 2.76,0.86 false 1.896,1.56 2.02,1.725 0.123,0.165 10 5 2.452,1.906 2.452,1.639 2.452,1.639 2.014,1.639 false 2.909,2.989 3.032,3.154 0.123,0.165 10 1 2.14,2.759 2.263,2.924 0.123,0.165 10 2 2.297,2.309 2.297,2.842 2.297,2.842 2.251,2.842 false 2.782,0.782 2.906,0.947 0.123,0.165 10 3 2.594,2.309 2.594,3.083 2.594,3.083 2.547,3.083 false 2.426,2.989 2.549,3.154 0.123,0.165 10 4 2.852,2.309 2.852,3.083 2.852,3.083 2.898,3.083 false
*1 Stop Light Control Relay (STOP Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)

NG

REPLACE STOP LIGHT CONTROL RELAY (STOP RELAY)

8.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)
a.

Install the stop light control relay (STOP relay).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Turn the power switch on (IG).


e.
C249762C49
0.208,0.802 0.625,1.073 0.417,0.271 1.344,1.75 0.698,2.917 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A28 0.51,2.938 0.948,3.208 0.438,0.271 10 false STP0
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-3 (STP0) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP0 CIRCUIT)

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C249762C50
0.208,0.802 0.625,1.073 0.417,0.271 1.542,2.156 0.688,2.896 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A28 0.531,2.927 0.938,3.208 0.406,0.281 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A28-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)