Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1391/69  Accumulator Leak Malfunction  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1391/69 Accumulator Leak Malfunction 351 Either of the following is detected:
1.

Accumulator pressure sensor input does not increase before braking or while the pump motor is operating.

2.

Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating.


·

Brake fluid leaks

·

Brake actuator (Brake booster with master cylinder assembly)

(Malfunctioning internal seal, low gas pressure in accumulator, etc.)


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK FOR FLUID LEAK
a.

Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.


b.

Check that the brakes are not dragging.

OK:

There are no fluid leaks or dragging.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE APPLICABLE PART

2.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1391/69 is output. A
DTC C1391/69 is not output. B



A

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SMC/SRC/SCC)
50004 105 89
HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).




e.

Perform the Active Test of the solenoid using the intelligent tester.


f.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

g.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator (brake booster with master cylinder assembly).



Result:
Result Proceed to
The output value of the wheel cylinder pressure sensor increases. A
The output values of the wheel cylinder pressure sensor does not increase. B



A

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Replace the brake actuator (brake booster with master cylinder assembly).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE BRAKE BOOSTER PUMP ASSEMBLY