Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM2040EQ _54 Brake _014709 BRAKE SYSTEM (OTHER) _0074989 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 4. DISABLE BRAKE CONTROL

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately clean it off.


Hide 53295E 6.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 47220D 11.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 47238C 12.SEPARATE RESERVOIR TUBE

Hide 44571A 13.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C243031

Move the clip and disconnect the No. 1 brake actuator hose from the brake booster pump assembly.


Hide 47233 14.REMOVE RESERVOIR BRACKET

a.
C243029

Remove the 2 bolts and reservoir bracket from the brake actuator bracket assembly.


Hide 47070 15.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C243032

Disconnect the 2 connectors from the brake booster pump assembly.


b.
C243033

Using a union nut wrench, disconnect the front No. 1 brake tube from the brake booster pump assembly.


c.
C243034C02
1.208,2.552 0.708,2.552 false 1.719,3.208 1.292,4.177 1.292,4.177 1.448,3.302 false 2.615,3.656 2.615,4.146 2.615,4.146 2.042,3.948 false 0.552,2.469 0.844,2.74 0.292,0.271 9 false *1 1.198,4.198 1.469,4.458 0.271,0.26 9 false *2 2.542,4.167 2.823,4.427 0.281,0.26 9 false *3
*1 Union
*2 Connector
*3 Stud


Remove the 2 nuts, brake booster pump assembly, 2 brake actuator case collars and 2 brake booster pump bushings from the brake actuator bracket assembly.

NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in bold in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Do not kink or damage the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 16.REMOVE FRONT WHEEL LH

Hide 44590 17.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY

a.
C243036

Disengage the 2 clamps to separate the 2 wire harnesses from the brake actuator bracket assembly.


b.
C243037

Disengage the clamp to separate the front No. 5 brake tube from the brake actuator bracket assembly.


c.
C243038

Remove the 3 bolts and brake actuator bracket assembly from the vehicle body.