Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  U0073/94  Control Module Communication Bus OFF  U0123/62  Lost Communication with Yaw Rate Sensor Module  U0124/95  Lost Communication with Lateral Acceleration Sensor Module  U0126/63  Lost Communication with Steering Angle Sensor Module  U0293/59  Communication Error from HV ECU  


DESCRIPTION

The skid control ECU receives signals from the power management control ECU, steering angle sensor and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
U0073/94 Control Module Communication Bus OFF 461
462
463
464
465
466
·

INF Code: 461

·

Either of the following is detected:

1.

Yaw rate and acceleration sensor communication is disabled for 1 second or more.

2.

Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.




·

INF Code: 462

·

Either of the following is detected:

1.

Steering angle sensor communication is disabled for 1 second or more.

2.

Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.




·

INF Code: 463, 464

·

Bus off occurs once or more per 0.1 seconds 10 times repeatedly.



·

INF Code: 465, 466

·

Sending does not complete within 5 seconds after data is output from the skid control ECU.



·

INF Code: 461

·

CAN communication line (V bus)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 462

·

CAN communication line (V bus)

·

Steering angle sensor

·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 463, 464, 465, 466

·

CAN communication line

·

Skid control ECU (Brake booster with master cylinder assembly)



Electronically controlled brake system DTC
U0123/62 Lost Communication with Yaw Rate Sensor Module 731
732
·

INF Code: 731

·

Yaw rate sensor communication is disabled for 1 second or more.



·

INF Code: 732

·

Yaw rate sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


VSC DTC
U0124/95 Lost Communication with Lateral Acceleration Sensor Module 591
592
·

INF Code: 591

·

Acceleration sensor communication is disabled for 1 second or more.



·

INF Code: 592

·

Acceleration sensor communication is disabled once per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC
U0126/63 Lost Communication with Steering Angle Sensor Module 741
742
·

INF Code: 741

·

Steering angle sensor communication is disabled for 1 second or more.



·

INF Code: 742

·

Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Steering angle sensor

·

Skid control ECU (Brake booster with master cylinder assembly)


VSC DTC
U0293/59 Communication Error from HV ECU 411
412
413
Either of the following is detected:
1.

With the IG2 terminal voltage 9.5 V or more, data from the power management control ECU cannot be received for 2 seconds or more.

2.

With the IG2 terminal voltage 9.5 V or more, data from the power management control ECU cannot be received once or more within 5 seconds occur 10 times in succession.


·

CAN communication line (Sub bus 15)

·

Power management control ECU

·

Skid control ECU (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC

WIRING DIAGRAM

C253837E02
5.052,4.323 5.49,4.323 5.49,4.323 5.49,4.49 false 3.042,3.375 3.469,3.375 3.469,3.375 3.469,3.552 false 0.26,3 1.5,3.427 1.24,0.427 10 false Power Management Control ECU 0.333,5.063 2.469,5.49 2.135,0.427 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.448,7.063 1.396,7.479 0.948,0.417 10 false Steering Angle Sensor 1.302,1.969 1.49,2.115 0.188,0.146 10 false 25 5.708,0.979 5.938,1.198 0.229,0.219 10 false 34 5.708,0.417 6.021,0.698 0.313,0.281 10 false 35 1.302,2.531 1.49,2.677 0.188,0.146 10 false 24 2.875,0.385 3.063,0.542 0.188,0.156 10 false 3 1.302,6.646 1.417,6.802 0.115,0.156 10 false 2 1.302,6.104 1.479,6.26 0.177,0.156 10 false 3 2.875,0.948 3.073,1.104 0.198,0.156 10 false 9 0.844,2.063 1.354,2.281 0.51,0.219 10 false CA1H 0.833,2.615 1.26,2.76 0.427,0.146 10 false CA1L 5.958,1.063 6.365,1.208 0.406,0.146 10 false CA2L 5.958,0.521 6.385,0.667 0.427,0.146 10 false CA2H 0.844,6.74 1.25,6.885 0.406,0.146 10 false CANL 0.823,6.177 1.25,6.323 0.427,0.146 10 false CANH 0.083,3.01 0.333,3.24 0.25,0.229 10 false I4 3.156,1.354 4.438,1.51 1.281,0.156 10 false Junction Connector 0.198,7.063 0.5,7.26 0.302,0.198 10 false I30 0.083,5.042 0.354,5.188 0.271,0.146 10 false I47 1.302,0.417 1.594,0.667 0.292,0.25 10 false 31 1.302,0.979 1.667,1.24 0.365,0.26 10 false 30 0.844,0.521 1.51,0.823 0.667,0.302 10 false CA3P 0.844,1.052 1.448,1.281 0.604,0.229 10 false CA3N 5.958,2.646 6.542,2.896 0.583,0.25 10 false CA1L 5.958,2.083 6.448,2.281 0.49,0.198 10 false CA1H 5.708,1.969 5.99,2.24 0.281,0.271 10 false 37 5.708,2.552 6,2.781 0.292,0.229 10 false 38 4.677,7.063 5,7.208 0.323,0.146 10 false A28 4.99,7.063 7.083,7.417 2.094,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.813,2.042 2.156,2.188 0.344,0.146 10 false I109 4.208,0.385 4.396,0.542 0.188,0.156 10 false 1 4.208,0.948 4.396,1.104 0.188,0.156 10 false 7 1.917,1.844 2.094,2 0.177,0.156 10 false 1 1.917,2.417 2.094,2.573 0.177,0.156 10 false 2 5.198,4.51 5.906,4.833 0.708,0.323 10 false Junction Connector 2.813,1.354 3.125,1.5 0.313,0.146 10 false A72 1.813,2.635 2.156,2.781 0.344,0.146 10 false I109 5.146,2.042 5.49,2.188 0.344,0.146 10 false I110 5.146,2.635 5.49,2.781 0.344,0.146 10 false I110 5.24,1.844 5.417,2 0.177,0.156 10 false 1 5.24,2.417 5.417,2.573 0.177,0.156 10 false 2 1.823,4.125 2.25,4.302 0.427,0.177 10 false I103 1.823,4.677 2.25,4.885 0.427,0.208 10 false I103 1.917,3.854 2.094,4.01 0.177,0.156 10 false 1 1.917,4.427 2.094,4.583 0.177,0.156 10 false 2 3.167,2.073 3.51,2.219 0.344,0.146 10 false I93 3.167,2.646 3.51,2.792 0.344,0.146 10 false I93 3.219,1.875 3.396,2.031 0.177,0.156 10 false 1 3.219,2.448 3.396,2.604 0.177,0.156 10 false 2 3.833,2.073 4.177,2.219 0.344,0.146 10 false I101 3.833,2.656 4.177,2.802 0.344,0.146 10 false I101 3.927,1.875 4.104,2.031 0.177,0.156 10 false 1 3.927,2.448 4.104,2.604 0.177,0.156 10 false 2 1.302,4.542 1.51,4.698 0.208,0.156 10 false 22 1.302,3.99 1.51,4.146 0.208,0.156 10 false 13 0.844,4.667 1.375,4.885 0.531,0.219 10 false CANL 0.813,4.115 1.24,4.26 0.427,0.146 10 false CANH 3.875,6.167 4.219,6.313 0.344,0.146 10 false I97 3.875,6.729 4.219,6.875 0.344,0.146 10 false I97 3.938,5.969 4.115,6.125 0.177,0.156 10 false 1 3.938,6.531 4.115,6.688 0.177,0.156 10 false 2 3.177,3.563 3.885,3.885 0.708,0.323 10 false Junction Connector

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Open Yaw rate sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
HV Communication Open Hybrid vehicle communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Yaw Rate Open
Steering Open
HV Communication Open
50003 105 205,207,217
Result:
Result Proceed to
There is a constant open circuit. A
There are no momentary interruptions. B
There are momentary interruptions. C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.




A

2.CHECK IF EACH SENSOR AND ECU CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECU CONNECTOR IS SECURELY CONNECTED
a.

Turn the power switch off.


b.

Check if each sensor and ECU connector is securely connected.

OK:

Each sensor and ECU connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECU CORRECTLY

3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Record the output DTCs (for the ABS, VSC, electronically controlled brake system and/or CAN communication system).

for ABS, VSC and Electronically Controlled Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

for CAN Communication System: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If the CAN communication system DTC and relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.



Result:
Result Proceed to
DTC is not output. A
ABS, VSC and/or electronically controlled brake system DTC is output. B
CAN communication system DTC is output. C



A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the power switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruptions between the skid control ECU (brake booster with master cylinder assembly) and each sensor or ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


f.

If ABS, VSC and/or electronically controlled brake system DTCs are output, record them.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output. A
ABS, VSC and/or electronically controlled brake system DTC is output. B
CAN communication system DTC is output. C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for ABS, VSC and/or electronically controlled brake system).




A

END

B

C