Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.02–2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.

·

There is a malfunction in the skid control ECU (brake booster with master cylinder assembly) internal circuit.

·

There is an open in the wire harness between the combination meter assembly and the skid control ECU (brake booster with master cylinder assembly).

·

The ABS control system is defective.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU (brake booster with master cylinder assembly) is malfunctioning.


WIRING DIAGRAM

C248086E07
0.688,0.781 1.25,1 0.563,0.219 10 false CANL 0.688,1.323 1.313,1.583 0.625,0.26 10 false CANH 1.177,0.688 1.573,0.938 0.396,0.25 10 false 15 1.177,1.229 1.521,1.438 0.344,0.208 10 false 16 0.083,5.844 0.427,6.073 0.344,0.229 10 false I18 0.385,5.844 1.594,6.385 1.208,0.542 10 false Combination Meter Assembly 1.938,1.875 3.469,2.125 1.531,0.25 10 false from IG1 NO. 2 Relay 4.198,2.021 5.406,2.25 1.208,0.229 10 false ECU-IG1 NO. 1 6.115,0.76 6.667,1.104 0.552,0.344 10 false CA1L 6.135,1.292 6.656,1.5 0.521,0.208 10 false CA1H 6.146,1.854 6.5,2.083 0.354,0.229 10 false IG1 6.125,2.385 6.729,2.667 0.604,0.281 10 false GND 5.01,5.844 7.083,6.333 2.073,0.49 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 6.125,2.854 6.813,3.125 0.688,0.271 10 false GND2 6.135,3.396 6.667,3.646 0.531,0.25 10 false GND3 6.135,3.917 6.698,4.167 0.563,0.25 10 false GND4 6.125,4.448 6.729,4.708 0.604,0.26 10 false GND5 6.146,4.927 6.667,5.146 0.521,0.219 10 false GND6 5.854,0.667 6.167,0.917 0.313,0.25 10 false 38 5.854,1.198 6.208,1.406 0.354,0.208 10 false 37 5.854,1.781 6.208,2.031 0.354,0.25 10 false 16 5.854,2.313 6.198,2.573 0.344,0.26 10 false 28 5.854,2.802 6.198,3.01 0.344,0.208 10 false 27 5.854,3.323 6.385,3.656 0.531,0.333 10 false 26 5.854,3.844 6.281,4.125 0.427,0.281 10 false 25 5.854,4.354 6.198,4.583 0.344,0.229 10 false 24 5.854,4.854 6.198,5.094 0.344,0.24 10 false 23 4.688,5.844 5.083,6.083 0.396,0.24 10 false A28

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO SKID CONTROL ECU CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C249762C51
0.208,0.802 0.625,1.073 0.417,0.271 1.344,1.865 0.688,2.896 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A28 0.594,2.948 1.198,3.427 0.604,0.479 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C249762C52
0.208,0.802 0.625,1.073 0.417,0.271 2.063,1.802 1.521,0.99 false 2.156,1.802 1.729,0.729 false 2.646,2.042 3.031,2.813 false 2.188,0.99 2.26,1.802 false 2.5,0.719 2.365,1.802 false 2.469,1.802 2.75,0.979 false 0.198,0.188 0.635,0.531 0.438,0.344 10 false *a 0.302,0.854 1.094,1.25 0.792,0.396 10 false A28 1.25,0.792 1.75,1.042 0.5,0.25 10 false GND6 1.531,0.531 1.948,0.781 0.417,0.25 10 false GND5 1.979,0.771 2.479,1.01 0.5,0.24 10 false GND4 2.354,0.521 2.771,0.76 0.417,0.24 10 false GND3 2.906,2.844 3.26,3 0.354,0.156 10 false GND 2.615,0.771 3.198,1.01 0.583,0.24 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-28 (GND) - Body ground Always Below 1 Ω
A28-27 (GND2) - Body ground Always Below 1 Ω
A28-26 (GND3) - Body ground Always Below 1 Ω
A28-25 (GND4) - Body ground Always Below 1 Ω
A28-24 (GND5) - Body ground Always Below 1 Ω
A28-23 (GND6) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST


c.

Check the combination meter assembly.

OK:

The ABS warning light turns on or off in accordance with intelligent tester operation.



HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY