Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.02–2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.

WIRING DIAGRAM

C212028E12
5.969,0.719 6.438,0.948 0.469,0.229 10 false CA1L 5.698,0.635 6.063,0.854 0.365,0.219 10 false 38 5.698,1.542 6,1.802 0.302,0.26 10 false 37 4.198,0.51 4.5,0.76 0.302,0.25 10 false 24 4.198,1.438 4.531,1.708 0.333,0.271 10 false 25 2.917,0.979 3.177,1.229 0.26,0.25 10 false 11 5.969,1.635 6.542,1.969 0.573,0.333 10 false CA1H 3.635,0.729 4.135,0.938 0.5,0.208 10 false CA1L 3.615,1.635 4.094,1.906 0.479,0.271 10 false CA1H 0.948,1.188 1.26,1.438 0.313,0.25 10 false TC 3.302,1.198 3.667,1.521 0.365,0.323 10 false TC 1.26,1.094 1.604,1.344 0.344,0.25 10 false 13 1.25,3.01 1.354,3.167 0.104,0.156 10 false 4 0.948,3.115 1.313,3.406 0.365,0.292 10 false CG 0.448,4.125 0.875,4.438 0.427,0.313 10 false I39 0.76,4.135 1.198,4.417 0.438,0.281 10 false DLC3 3.052,4.115 4.302,4.563 1.25,0.448 10 false Power Management Control ECU 5,4.125 7.104,4.49 2.104,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.219,0.719 4.646,0.99 0.427,0.271 10 false I4 4.219,1.646 4.573,1.917 0.354,0.271 10 false I4 2.948,1.188 3.271,1.344 0.323,0.156 10 false I3 5.969,2.625 6.438,2.896 0.469,0.271 10 false CA2L 5.698,2.521 5.99,2.76 0.292,0.24 10 false 34 5.698,3.448 6.01,3.708 0.313,0.26 10 false 35 4.188,2.406 4.49,2.688 0.302,0.281 10 false 30 4.208,3.344 4.542,3.604 0.333,0.26 10 false 31 5.969,3.563 6.469,3.823 0.5,0.26 10 false CA2H 3.625,2.625 4.063,2.823 0.438,0.198 10 false CA3N 3.646,3.563 4.26,3.896 0.615,0.333 10 false CA3P 4.219,2.615 4.521,2.771 0.302,0.156 10 false I4 4.229,3.563 4.604,3.792 0.375,0.229 10 false I4 4.688,4.125 4.99,4.281 0.302,0.156 10 false A28

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - I3-11 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C68
0.229,1.125 0.625,1.375 0.396,0.25 2.104,0.917 1.635,1.896 false 0.167,0.167 0.49,0.542 0.323,0.375 10 false *a 2.052,0.719 2.385,1.01 0.333,0.292 10 false CG 0.344,1.177 0.698,1.448 0.354,0.271 10 false I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
C207407C69
0.219,0.979 0.667,1.271 0.448,0.292 1.823,2.354 2.552,0.917 false 0.26,0.25 0.573,0.531 0.313,0.281 10 false *a 2.5,0.698 2.875,0.99 0.375,0.292 10 false TC 0.365,1.042 0.76,1.333 0.396,0.292 10 false I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU