Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TS and CG of the DLC3 causes the ECU to display Test Mode DTCs by blinking the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.

In Test Mode (signal check), a malfunction in a speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the power switch from off to on (IG).

WIRING DIAGRAM

C243629E30
5.969,0.635 6.365,0.792 0.396,0.156 10 false CA1L 4.698,1.844 5.063,2.104 0.365,0.26 10 false A28 5.698,0.583 5.948,0.823 0.25,0.24 10 false 38 5.698,1.281 6,1.5 0.302,0.219 10 false 37 5.969,1.333 6.385,1.49 0.417,0.156 10 false CA1H 0.927,0.708 1.406,0.938 0.479,0.229 10 false CANL 0.906,1.406 1.49,1.646 0.583,0.24 10 false CANH 5.969,2.958 6.333,3.229 0.365,0.271 10 false TS 1.094,2.969 1.438,3.26 0.344,0.292 10 false TS 5.698,2.865 5.938,3.115 0.24,0.25 10 false 12 5.771,3.49 5.938,3.719 0.167,0.229 10 false 4 5.969,3.583 6.292,3.823 0.323,0.24 10 false CG 6.021,4.146 6.385,4.396 0.365,0.25 10 false I39 6.292,4.146 6.781,4.396 0.49,0.25 10 false DLC3 5.01,1.854 7.052,2.281 2.042,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.458,4.104 1.427,4.583 0.969,0.479 10 false Power Steering ECU Assembly 0.26,4.115 0.594,4.333 0.333,0.219 10 false j3 1.417,0.583 1.688,0.854 0.271,0.271 10 false 8 1.417,1.292 1.823,1.615 0.406,0.323 10 false 4 1.396,2.865 1.719,3.115 0.323,0.25 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C207407C70
0.198,1.125 0.594,1.375 0.396,0.25 2.281,1.146 1.635,2.365 false 1.458,0.729 1.635,1.906 false 0.167,0.167 0.49,0.542 0.323,0.375 10 false *a 2.188,0.948 2.521,1.24 0.333,0.292 10 false TS 0.302,1.177 0.656,1.448 0.354,0.271 10 false I39 1.344,0.531 1.677,0.823 0.333,0.292 10 false CG
*a Front view of DLC3


Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I39-12 (TS) - I39-4 (CG) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)

NG

4.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
3.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)
a.
C207407C70
0.198,1.125 0.594,1.375 0.396,0.25 2.281,1.146 1.635,2.365 false 1.458,0.729 1.635,1.906 false 0.167,0.167 0.49,0.542 0.323,0.375 10 false *a 2.188,0.948 2.521,1.24 0.333,0.292 10 false TS 0.302,1.177 0.656,1.448 0.354,0.271 10 false I39 1.344,0.531 1.677,0.823 0.333,0.292 10 false CG
*a Front view of DLC3


Turn the power switch off.


b.

Using SST, connect terminals TS and CG of the DLC3.


SST
09843-18040  

c.

Check that the P/S warning light is blinking.

OK:

The P/S warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR POWER STEERING ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the j3 power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-12 (TS) - j3-5 (TS) Always Below 1 Ω
I39-12 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C71
0.229,1.125 0.625,1.375 0.396,0.25 2.104,0.917 1.635,1.896 false 0.167,0.167 0.49,0.542 0.323,0.375 10 false *a 2.052,0.719 2.385,1.01 0.333,0.292 10 false CG 0.344,1.177 0.698,1.448 0.354,0.271 10 false I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)
a.
C207407C70
0.198,1.125 0.594,1.375 0.396,0.25 2.281,1.146 1.635,2.365 false 1.458,0.729 1.635,1.906 false 0.167,0.167 0.49,0.542 0.323,0.375 10 false *a 2.188,0.948 2.521,1.24 0.333,0.292 10 false TS 0.302,1.177 0.656,1.448 0.354,0.271 10 false I39 1.344,0.531 1.677,0.823 0.333,0.292 10 false CG
*a Front view of DLC3


Reconnect the j3 power steering ECU assembly connector.


b.

Using SST, connect terminals TS and CG of the DLC3.


SST
09843-18040  

c.

Check that the P/S warning light is blinking.

OK:

The P/S warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR POWER STEERING ECU ASSEMBLY