Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1203/95  ECM Communication Circuit Malfunction  


DESCRIPTION

This circuit is used to send TRC and VSC information from the skid control ECU to the power management control ECU, and hybrid control system information from the power management control ECU to the skid control ECU via the CAN communication system.

Identification information sent from other ECUs is stored when shipped from the factory and used as default values.

NOTICE:

DTC C1203/95 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from that stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1203/95 ECM Communication Circuit Malfunction - Either of the following is detected:
1.

Identification information sent from other ECUs does not match with the value stored when shipped from the factory.

2.

No stored information for destination.


·

The wrong ECU or sensor was installed

·

Skid control ECU (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK PART NUMBER
a.

Check that the proper power management control ECU, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) are installed.

OK:

Proper ECUs and sensor are installed.



b.

Check if the power management control ECU, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) were replaced before the DTC was recorded.

OK:

ECU or sensor was not replaced.



Result:
Result Proceed to
OK A
NG (A proper power management control ECU is not installed and/or the power management control ECU was replaced.) B
NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.) C
NG (A proper yaw rate and acceleration sensor (airbag sensor assembly) is not installed and/or the yaw rate and acceleration sensor (airbag sensor assembly) was replaced.) D



A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167
HINT:

Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.



Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1203/95 is output. A
DTC C1203/95 is not output. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END