Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1231/31  Steering Angle Sensor Circuit Malfunction  


DESCRIPTION

The skid control ECU receives steering angle sensor signals via the CAN communication system. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126/63 (Lost Communication with Steering Angle Sensor Module) is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1231/31 Steering Angle Sensor Circuit Malfunction 701
702
703
·

INF Code: 701

·

While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction).


·

INF Code: 702

·

While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction).


·

INF Code: 703

·

While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction).



Steering angle sensor internal malfunction VSC DTC

WIRING DIAGRAM

C167662E75
0.146,3.927 0.469,4.135 0.323,0.208 10 false I30 0.896,3.302 1.26,3.5 0.365,0.198 10 false ESS 0.813,0.667 1.344,0.927 0.531,0.26 10 false CANL 0.802,1.26 1.24,1.479 0.438,0.219 10 false CANH 0.917,1.948 1.365,2.198 0.448,0.25 10 false BAT 1.031,2.625 1.333,2.885 0.302,0.26 10 false IG 1.292,0.563 1.604,0.896 0.313,0.333 10 false 2 1.281,1.135 1.469,1.323 0.188,0.188 10 false 3 1.292,1.844 1.417,2.031 0.125,0.188 10 false 5 1.292,2.521 1.5,2.865 0.208,0.344 10 false 4 1.302,3.188 1.521,3.469 0.219,0.281 10 false 1 2.063,2.094 2.948,2.25 0.885,0.156 10 false ECU-B NO. 1 2.01,2.781 3.052,2.938 1.042,0.156 10 false ECU-IG1 NO. 1 3.906,1.938 5.51,2.354 1.604,0.417 10 false from Auxiliary Battery 3.906,2.604 5.458,2.854 1.552,0.25 10 false from IG1 NO. 2 Relay 5.792,1.135 6.073,1.396 0.281,0.26 10 false 37 5.042,3.885 5.469,4.167 0.427,0.281 10 false A28 6.042,0.667 6.552,0.99 0.51,0.323 10 false CA1L 6.042,1.229 6.542,1.563 0.5,0.333 10 false CA1H 5.781,0.563 6.083,0.906 0.302,0.344 10 false 38 5.042,4.042 7.156,4.417 2.115,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.135,4.083 1.646,4.385 1.51,0.302 10 false Steering Angle Sensor 2.625,2.51 2.729,2.698 0.104,0.188 10 false 1 2.625,1.833 2.865,2.083 0.24,0.25 10 false 1 2.229,1.833 2.385,2.021 0.156,0.188 10 false 2 2.229,2.521 2.427,2.708 0.198,0.188 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

When U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0126/63 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94

·

When a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1231/31 is output. A
CAN communication system DTC is output. B
Speed sensor and/or yaw rate and acceleration sensor DTC is output. C
DTC C1231/31 is not output. D


HINT:
·

When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.

·

If there is a malfunction in the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor is normal.

·

If speed sensor and the yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.





A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

C

D

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C156493C46
0.26,0.938 0.635,1.177 0.375,0.24 2.635,2.01 1.906,2.552 false 2.104,2.698 2.625,2.958 false 0.375,0.969 0.719,1.302 0.344,0.333 10 false I30 2.667,1.906 2.99,2.167 0.323,0.26 10 false IG 2.667,2.896 3.188,3.167 0.521,0.271 10 false BAT 0.25,0.208 0.563,0.479 0.313,0.271 10 false *a
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the power switch off.


b.

Remove the steering wheel and the column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the I30 steering angle sensor connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I30-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
I30-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C156493C47
0.365,1.115 0.771,1.385 0.406,0.271 1.333,2.698 0.865,2.938 false 0.229,0.229 0.542,0.542 0.313,0.313 10 false *a 0.5,1.167 0.854,1.458 0.354,0.292 10 false I30 0.542,2.875 0.906,3.208 0.365,0.333 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I30-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)