Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1247/47  Stroke Sensor Malfunction  C1346/71  Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC)  C1392/48  Stroke Sensor Zero Point Calibration Undone  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU.

DTC C1346/71 will be cleared when the brake pedal stroke sensor assembly sends a brake pedal stroke sensor assembly signal or when Test Mode ends. DTC C1346/71 is output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1247/47 Stroke Sensor Malfunction 211
212
213
214
215
218
219
223
·

INF Code: 211

·

Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.


·

INF Code: 212

·

Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.


·

INF Code: 213

·

Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more.


·

INF Code: 214

·

Either of the following is detected:

1.

Fluctuation of sensor output 1 (SKS1) is out of specification.

2.

The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.



·

INF Code: 215

·

Either of the following is detected:

1.

Fluctuation of sensor output 2 (SKS2) is out of specification.

2.

The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.



·

INF Code: 218

·

An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more.


·

INF Code: 219

·

Sensor data is invalid for 0.2 seconds or more.

(Skid control ECU internal monitor circuit malfunction.)


·

INF Code: 223

·

Sensor data is invalid for 0.2 seconds or more.

(Open, short, or noise.)



·

INF Code: 211

·

Open or short in brake pedal stroke sensor assembly power supply circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 212, 213, 214, 215, 218, 219, 223

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly



Electronically controlled brake system DTC
C1346/71 Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC) - Detected only during Test Mode.
·

Brake pedal stroke sensor assembly

·

Brake pedal stroke sensor assembly circuit


Electronically controlled brake system Test Mode DTC
C1392/48 Stroke Sensor Zero Point Calibration Undone - Zero point calibration of brake pedal stroke sensor assembly is unfinished.
·

Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)

·

Skid control ECU (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC

WIRING DIAGRAM

C235540
0.438,4 1.677,4.375 1.24,0.375 10 false Brake Pedal Stroke Sensor Assembly 0.792,1.396 1.573,1.74 0.781,0.344 10 false SKS1 0.76,2.948 1.635,3.271 0.875,0.323 10 false VCSK 0.865,2.146 1.615,2.563 0.75,0.417 10 false SKG 0.792,0.604 1.656,0.948 0.865,0.344 10 false SKS2 5.979,1.396 6.771,1.885 0.792,0.49 10 false SKS 5.979,2.927 6.802,3.281 0.823,0.354 10 false VCSK 5.979,2.125 6.729,2.51 0.75,0.385 10 false SKG 5.979,0.583 6.604,0.948 0.625,0.365 10 false SKS2 1.292,0.49 1.885,0.802 0.594,0.313 10 false 4 1.292,1.292 1.875,1.635 0.583,0.344 10 false 2 1.292,2.021 1.875,2.385 0.583,0.365 10 false 1 1.302,2.823 1.906,3.104 0.604,0.281 10 false 3 4.635,4 5.229,4.302 0.594,0.302 10 false A28 5.708,2.823 6.385,3.24 0.677,0.417 10 false 39 5.708,1.281 6.271,1.646 0.563,0.365 10 false 42 5.708,2.021 6.083,2.281 0.375,0.26 10 false 41 5.01,4 7.094,4.365 2.083,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.052,4 0.604,4.292 0.552,0.292 10 false A41 5.708,0.479 6.271,0.885 0.563,0.406 10 false 40

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT


c.

Adjust the brake pedal stroke sensor assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector and the A41 brake pedal stroke sensor assembly connector.


c.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-39 (VCSK) - A41-3 (VCSK) Always Below 1 Ω
A28-39 (VCSK) - Body ground Always 10 kΩ or higher
A28-41 (SKG) - A41-1 (SKG) Always Below 1 Ω
A28-41 (SKG) - Body ground Always 10 kΩ or higher
A28-42 (SKS) - A41-2 (SKS1) Always Below 1 Ω
A28-42 (SKS) - Body ground Always 10 kΩ or higher
A28-40 (SKS2) - A41-4 (SKS2) Always Below 1 Ω
A28-40 (SKS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C234579
0.302,1.01 0.729,1.323 0.427,0.313 1.25,2.281 0.865,2.823 false 1.698,2.302 2.083,2.844 false 0.281,0.24 0.781,0.677 0.5,0.438 10 false *a 0.406,1.083 1.146,1.542 0.74,0.458 10 false A41 0.688,2.854 1.292,3.125 0.604,0.271 10 false SKG 1.99,2.865 2.813,3.24 0.823,0.375 10 false VCSK
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-3 (VCSK) - A41-1 (SKG) Power switch on (IG) 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY