Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1252/52  Brake Booster Pump Motor on Time Abnormally Long  C1253/53  Pump Motor Relay Malfunction  


DESCRIPTION

The skid control ECU detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1252/52 Brake Booster Pump Motor on Time Abnormally Long 311 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction for 98 seconds or more.)
·

Short in motor circuit or motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction in brake actuator (Brake booster with master cylinder assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1253/53 Pump Motor Relay Malfunction 321
322
323
324
325
326
327
328
329
·

INF Code: 321

·

With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request.


·

INF Code: 322

·

The motor drive monitor remains on for 2 seconds or more after a motor drive off request.


·

INF Code: 323

·

The skid control ECU internal motor drive logical inconsistency continues for 2 seconds or more.


·

INF Code: 324

·

An open circuit in both skid control ECU internal motor relays 1 and 2.


·

INF Code: 325

·

An open circuit in both skid control ECU internal motor relays 1 and 3.


·

INF Code: 326

·

An open circuit in both skid control ECU internal motor relays 2 and 3.


·

INF Code: 327

·

An open circuit in skid control ECU internal motor relay 1.


·

INF Code: 328

·

An open circuit in skid control ECU internal motor relay 2.


·

INF Code: 329

·

An open circuit in skid control ECU internal motor relay 3.



·

INF Code: 321, 324, 325, 326, 327, 328, 329

·

Open in motor circuit or motor monitor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 322

·

Short in motor circuit or motor monitor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 323

·

Skid control ECU (Brake booster with master cylinder assembly)



Electronically controlled brake system DTC

WIRING DIAGRAM

C252440E06
3.823,3.198 4.979,3.365 1.156,0.167 10 false ABS MTR NO. 1 2.771,5.604 3.469,5.99 0.698,0.385 10 false MAIN 0.104,8.073 1.448,8.438 1.344,0.365 10 false Brake Booster Pump Assembly 5.021,8.125 7.156,8.479 2.135,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.844,1.031 1.375,1.375 0.531,0.344 10 false BM1 0.833,2.094 1.406,2.5 0.573,0.406 10 false BM2 6.135,0.927 6.729,1.396 0.594,0.469 10 false MRO1 6.135,3.031 6.583,3.198 0.448,0.167 10 false MRI1 6.135,1.969 6.688,2.26 0.552,0.292 10 false MRO2 6.135,4.115 6.688,4.542 0.552,0.427 10 false MRI2 0.74,5.563 1.365,5.99 0.625,0.427 10 false GND1 6.135,5.021 6.563,5.188 0.427,0.167 10 false GND 0.729,6.552 1.344,6.906 0.615,0.354 10 false GND2 6.135,5.521 6.563,5.688 0.427,0.167 10 false GND2 6.135,5.969 6.563,6.135 0.427,0.167 10 false GND3 6.135,6.469 6.563,6.635 0.427,0.167 10 false GND4 6.135,6.927 6.563,7.094 0.427,0.167 10 false GND5 6.135,7.427 6.563,7.594 0.427,0.167 10 false GND6 5.927,4.021 6.104,4.167 0.177,0.146 10 false 2 5.927,2.938 6.156,3.104 0.229,0.167 10 false 1 5.865,1.885 6.135,2.177 0.271,0.292 10 false 30 5.875,0.823 6.208,1.281 0.333,0.458 10 false 29 1.354,6.229 1.583,6.396 0.229,0.167 10 false 1 2.844,7.198 4.146,7.552 1.302,0.354 10 false Auxiliary Battery 1.375,5.24 1.573,5.438 0.198,0.198 10 false 2 1.292,6.448 1.698,6.719 0.406,0.271 10 false A47 1.292,5.448 1.74,5.771 0.448,0.323 10 false A46 1.292,1.979 1.854,2.396 0.563,0.417 10 false A47 1.354,1.771 1.458,1.917 0.104,0.146 10 false 2 1.292,0.938 1.688,1.344 0.396,0.406 10 false A46 1.354,0.708 1.458,0.854 0.104,0.146 10 false 1 3.823,4.302 5.104,4.771 1.281,0.469 10 false ABS MTR NO. 2 5.875,4.917 6.198,5.292 0.323,0.375 10 false 28 5.875,5.406 6.115,5.635 0.24,0.229 10 false 27 5.875,5.896 6.188,6.198 0.313,0.302 10 false 26 5.885,6.365 6.135,6.635 0.25,0.271 10 false 25 5.875,6.854 6.135,7.125 0.26,0.271 10 false 24 5.865,7.323 6.156,7.708 0.292,0.385 10 false 23 5.031,7.958 5.354,8.125 0.323,0.167 10 false A28 2.542,5.365 2.771,5.531 0.229,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Motor Relay ABS motor relay Relay ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Motor Relay
50004 105 42

d.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay ABS motor relay ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Data List
Tester Display
ECB Motor Relay
50003 105 63

e.

Check the operating condition of the ABS motor relay when operating it using the intelligent tester.


Result:
Result Proceed to
ABS motor relay in the Data List turns ON/OFF using the Active Test. A
ABS motor relay in the Data List does not change using the Active Test. B



A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C156574C14
1.688,1.177 2.083,1.427 0.396,0.25 0.854,1.188 1.229,1.438 0.375,0.25 1,1.938 0.656,2.958 false 1.188,1.927 1.458,2.969 false 2.427,0.813 1.927,1.844 false 1.344,0.813 1.75,1.844 false 2.188,0.615 2.667,0.781 0.479,0.167 10 false GND2 0.469,2.979 1.042,3.26 0.573,0.281 10 false GND1 1.313,3 1.854,3.229 0.542,0.229 10 false BM1 1.156,0.615 1.531,0.771 0.375,0.156 10 false BM2 0.333,0.292 0.688,0.635 0.354,0.344 10 false *a 1.771,1.219 2.156,1.458 0.385,0.24 10 false A47 0.938,1.219 1.333,1.458 0.396,0.24 10 false A46
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A46 and A47 brake booster pump assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-1 (BM1) - A46-2 (GND1) Always Below 10 Ω
A47-2 (BM2) - A47-1 (GND2) Always Below 10 Ω
A46-1 (BM1) - A47-2 (BM2) Always Below 1 Ω
A46-2 (GND1) - A47-1 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C288262C01
0.5,0.552 0.875,0.781 0.375,0.229 0.5,2.771 0.875,3 0.375,0.229 1.26,4.25 1.51,3.76 false 1.958,1.5 2.396,2.031 false 0.573,0.583 1.031,0.781 0.458,0.198 10 false A46 0.583,2.813 1.042,3.01 0.458,0.198 10 false A47 0.177,0.115 0.635,0.313 0.458,0.198 10 false *a 2.281,2.063 2.74,2.26 0.458,0.198 10 false GND1 1.094,4.292 1.552,4.49 0.458,0.198 10 false GND2
*a Front view of wire harness connector
(to Brake Booster Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-2 (GND1) - Body ground Always Below 1 Ω
A47-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the A46 and A47 brake booster pump assembly connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

e.

Wait for 30 seconds without depressing the brake pedal.


f.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
5.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1252/52 and C1253/53 are not output. A
DTCs C1252/52 and/or C1253/53 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SMC/SRC/SCC)
50004 105 89

b.

Perform the Active Test of the solenoid using the intelligent tester.


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

d.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
a.
C249762C44
0.208,0.802 0.625,1.073 0.417,0.271 0.844,1.833 0.583,2.677 false 1.146,1.833 1.375,2.688 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.313,0.854 1,1.167 0.688,0.313 10 false A28 0.458,2.708 1.24,3.177 0.781,0.469 10 false MRI1 1.25,2.719 2.031,3.188 0.781,0.469 10 false MRI2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Check that the ABS MTR NO. 1 (50 A) and ABS MTR NO. 2 (50 A) fuses are normal.

HINT:

If the result is not as specified, replace the ABS MTR NO. 1 (fusible link block assembly) and/or ABS MTR NO.2 fuse (fusible link block assembly).



c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-1 (MRI1) - Body ground Always 11 to 14 V
A28-2 (MRI2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A46 and A47 brake booster pump assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-29 (MRO1) - A46-1 (BM1) Always Below 1 Ω
A28-29 (MRO1) - Body ground Always 10 kΩ or higher
A28-30 (MRO2) - A47-2 (BM2) Always Below 1 Ω
A28-30 (MRO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR